Garmin GSD 24 Installation Instructions - Page 1
Garmin GSD 24 Manual
View all Garmin GSD 24 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
GSD™ 24/26 Installation Instructions To obtain the best performance and to avoid damage to your boat, install the Garmin® GSD 24/26 unit according to the following instructions. Professional installation of the unit is highly recommended, because specific knowledge of boat construction is required to properly install the unit. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin Product Support. Registering Your Device Help us better support you by completing our online registration today. • Go to http://my.garmin.com. • Keep the original sales receipt, or a photocopy, in a safe place. Contacting Garmin Product Support Contact Garmin Product Support if you have any questions about this product. • In the USA, go to www.garmin.com/support, or contact Garmin USA by phone at (913) 397.8200 or (800) 800.1020. • In the UK, contact Garmin (Europe) Ltd. by phone at 0808 2380000. • In Europe, go to www.garmin.com/support and click Contact Support for in-country support. Important Safety Information Warning You are responsible for the safe and prudent operation of your vessel. Sonar is a tool that will enhance your awareness of the water beneath your boat. It does not relieve you from the responsibility of observing the water around your boat as you navigate. When drilling or cutting, always check the opposite side of the surface. Be aware of fuel tanks, electrical cables, and hydraulic hoses. caution Failure to install and maintain this equipment in accordance with these instructions could result in damage or injury. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. Notice This equipment must be installed by a qualified marine installer. Transducers A transducer is required to send and receive the sonar signal from the GSD 24/26. Proper transducer selection and installation are critical to the operation of the GSD 24/26. Because mounting locations vary, see your local Garmin dealer or contact Garmin Product Support for more information. Go to www.garmin.com to view a full list of transducers. GSD 24/26 Installation notice The GSD 24/26 must be installed according to the following instructions to get the best possible performance. If you experience difficulty with the installation, contact Garmin Product Support. Because every boat is different, you must carefully plan the GSD 24/26 sounder installation. 1 Select a mounting location (page 1). 2 Mount the sounder (page 1). 3 Connect the sounder to the Garmin Marine Network and to power (page 2). 4 Connect the sounder to the transducer (page 2). Tools Needed Note: If you are not using the mounting hardware included in the kit, use the most appropriate tool for securing that hardware. • Drill • #8 (5 mm) drill bit appropriate for mounting surface • 1 1/4 in. (32 mm) paddle drill bit or hole saw appropriate for mounting surface • #2 Phillips screwdriver • 3 mm flat screwdriver • Cable ties (optional) • Wire cutter • Wire stripper • 1 in. (24 mm) and /19 32 in. (15 mm) wrenches • Marine sealant (optional) Mounting the Sounder Mounting Location Considerations • The sounder dimensions and mounting hole locations can be reviewed on the templates included in the sounder package. • The sounder must be mounted in a location where it cannot be submerged. • The sounder must be mounted in a location with adequate ventilation where it will not be exposed to extreme temperatures. • The sounder should be mounted in such a way that the LED is visible. • The sounder should be mounted so that the power and network cables can be easily connected. • The sounder should be mounted so that the transducer cable can be connected. If required, transducer extension cables up to 20 ft. (6 m) are available through your Garmin dealer. Mounting the Sounder 1 After you select a mounting location (page 1), determine the mounting hardware needed for the surface. Mounting hardware is included with the sounder, but it may not be suitable for the mounting surface. 2 If necessary, purchase the mounting hardware. 3 Complete an action: • Hold the sounder in the intended mounting location and mark the locations of the mounting holes in the mounting surface, using the sounder as a template. • Use the template included with your sounder to mark the locations of the mounting holes. 4 Drill the mounting holes through the mounting surface. 5 Secure the sounder to the mounting surface using the selected mounting hardware. October 2011 190-00789-02_0C Printed in Taiwan