Garmin Varia Smart Bike Lights Owner s Manual - Page 7
Device Settings, Pairing Varia Bike Lights with Your Edge 1000
View all Garmin Varia Smart Bike Lights manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Device Settings You can remotely control your Varia devices and customize settings using your compatible Edge device. This section contains instructions for the Edge 1000 device. Other compatible Edge devices use similar settings. Pairing Varia Bike Lights with Your Edge 1000 Before you can pair the devices, you must update the Edge software. 1 Bring the Edge device within range (3 m) of the sensor. NOTE: Stay 10 m away from other ANT+® bike lights while pairing. 2 Turn on the Edge device. 3 From the home screen, select > Sensors > Add Sensor > Varia. 4 Turn on the Varia device. 5 Select the Varia device key to enter smart mode. The status LED flashes blue. 6 Select your sensor. When the sensor is paired with your Edge device, the status icon appears solid on the connections page. Turning Varia Devices On and Off with Your Edge 1000 Before you can turn Varia devices on and off with your Edge device, you must pair the devices (Pairing Varia Bike Lights with Your Edge 1000, page 3). • To turn on all paired lights, turn on your Edge device. • To turn off all paired lights, turn off your Edge device. Customizing Varia Device Settings with Your Edge 1000 Before you can customize Varia device settings with your Edge device, you must pair the devices (Pairing Varia Bike Lights with Your Edge 1000, page 3). 1 From your Edge device, select > Sensors > Varia. 2 Select an option: • Select Enable to enable the light network. • Select Configuration to set the light intensity mode for all lights in your network (Configuration Settings, page 3). • Select Beam Angle to automatically adjust the headlight beam angle based on the rate of speed. Higher beam angles are used at high speeds, and lower beam angles are used at low speeds. NOTE: This setting appears when a headlight is paired with the device. • Select Turn Signal Setup to configure turn signals when using two taillights (Turn Signal Settings, page 3). NOTE: This setting appears when two taillights are paired with the device. • Select Light Network to view device information and customize each light in your network (Light Network Settings, page 4). • Select Test Lights to check that each light in your network is set up correctly (Testing the Light Network, page 4). Configuration Settings From your Edge device, select > Sensors > Varia > Configuration. Auto: Automatically adjusts the light intensity based on the ambient light or time of day. Day: Sets the light intensity for day. Night: Sets the light intensity for night. Power Save: Automatically adjusts the light intensity based on the remaining battery life of the bike light. When battery life is low, the light intensity is reduced to prolong battery life. Individual: Allows you to customize the light intensity and pattern mode for each light in your network (Light Network Settings, page 4). Adjusting the Beam Angle During a Ride Before you can adjust the beam angle during a ride, you must disable the automatic beam angle setting (Customizing Varia Device Settings with Your Edge 1000, page 3). 1 Go for a ride. 2 Swipe the screen to view the bike lights data screen. 3 Select or to adjust the headlight beam angle. Turn Signal Settings From your Edge device, select > Sensors > Varia > Turn Signal Setup. Enable: Allows the paired Edge device to assign and control turn signals. Auto Cancel: Automatically cancels the turn signal after making a 90° turn. NOTE: Your paired Edge device must have GPS turned on in order to use the Auto Cancel setting. Right: Assigns the right turn signal. Left: Assigns the left turn signal. Assigning Turn Signals When using two taillights, you must indicate which light is the left turn signal and which light is the right turn signal. 1 Pair two taillights with your Edge device (Pairing Varia Bike Lights with Your Edge 1000, page 3). 2 From your Edge device, select > Sensors > Varia > Turn Signal Setup. 3 Select Right, and select a taillight to assign it as the right turn signal. When two taillights are paired, the Edge device assigns the second taillight as the left turn signal automatically. 4 If necessary, select Left, and select the second taillight to assign it as the left turn signal. Signaling a Turn with Your Edge 1000 WARNING The Varia device is not a substitute for other bike safety measures, such as hand signals, deferring to posted signs and conditions, and using good judgement. Before you can signal a turn with your Edge device, you must install two taillights (Installing the Multi-Location Mount, page 2) and assign turn signals to them (Assigning Turn Signals, page 3). 1 Go for a ride. 2 Tap the screen to view the timer overlay. Device Settings 3