Garmin Volvo Penta Glass Cockpit System Owner's Manual - Page 31

may resolve compatibility issues with older NMEA 0183 autopilots. Defaults: Restores the NMEA 0183 settings to the original factory defaults. Diagnostics: Displays NMEA 0183 diagnostic information. Configuring NMEA 0183 Output Sentences You can enable and disable NMEA 0183 output sentences. 1 Select Settings > Communications > NMEA 0183 Setup > Output Sentences. 2 Select an option. 3 Select one or more NMEA 0183 output sentences, and select Back. 4 Repeat steps 2 and 3 to enable or disable additional output sentences. Setting the Communication Format for Each NMEA 0183 Port You can configure the communication format for each internal NMEA 0183 port when connecting your chartplotter to external NMEA 0183 devices, a computer, or other Garmin devices. 1 Select Settings > Communications > NMEA 0183 Setup > Port Type. 2 Select an input or output port. 3 Select a format: • To support the input or output of standard NMEA 0183 data, DSC, and sonar NMEA input support for the DPT, MTW, and VHW sentences, select NMEA Std. . • To support the input or output of standard NMEA 0183 data for most AIS receivers, select NMEA High Speed. • To support the input or output of Garmin proprietary data for interfacing with Garmin software, select Garmin. 4 Repeat steps 2-3 to configure additional input or output ports. NMEA 2000 Settings Select Settings > Communications > NMEA 2000. Device List: Displays the devices connected to the network. Label Devices: Changes the labels for available connected devices. Garmin Marine Network The Garmin Marine Network allows you to share data from Garmin peripheral devices with the chartplotters quickly and easily. You can connect a chartplotter to a Garmin Marine Network to receive data from and share data with other Garmin Marine Network-compatible devices and chartplotters. EVC Network Select Settings > Communications > EVC Network, and select a driveline. For more information, refer to the Volvo Penta manual. Features: Shows a list of installed EVC features. Components: Shows a list of installed hardware components. Software: Shows a list of software versions for installed EVC features. Calibration: Shows a list of installed EVC features that can be calibrated. Setting Alarms Navigation Alarms Select Settings > Alarms > Navigation. Arrival: Sets an alarm to sound when you are within a specified distance or time from a turn or a destination. Anchor Drag: Sets an alarm to sound when you exceed a specified drift distance while anchored. Off Course: Sets an alarm to sound when you are off course by a specified distance. System Alarms Alarm Clock: Sets an alarm clock. Device Voltage: Sets an alarm to sound when the battery reaches a specified low voltage. GPS Accuracy: Sets an alarm to sound when the GPS location accuracy falls outside the user-defined value. Setting the Fuel Alarm You can set an alarm to sound when the total amount of remaining onboard fuel reaches the level you specify. 1 Select Settings > Alarms > Fuel. 2 If necessary, select a driveline. 3 Select On. 4 Enter the remaining amount of fuel that triggers the alarm. 5 If necessary, repeat steps 2-4 for all drivelines. Setting Weather Alarms Before you can set weather alarms, you must have a compatible chartplotter connected to a weather device, such as a GXM™ device, and have a valid weather subscription. 1 Select Settings > Alarms > Weather. 2 Turn on alarms for specific weather events. My Vessel Settings NOTE: Some settings and options require additional charts or hardware. Select Settings > My Vessel. For more information, refer to the Volvo Penta manual. Keel Offset: Offsets the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location (page 25). Temperature Offset: Compensates for the water temperature reading from a NMEA 0183 water-temperature sensor or a temperature-capable transducer (page 26). Calibrate Water Speed: Calibrates the speed-sensing transducer or sensor (page 26). e-KEY Management: Allows you to manage the electronic keys (e-KEYs). Drive Type: The setting should be changed by authorized Volvo Penta personnel only. ACP Mode: Sets the ACP protection mode. Toe Angle: The setting should be changed by authorized Volvo Penta personnel only. Speed Factor: Calibrates the displayed boat speed. PTA Settings: Allows you to enter new maximum limits for the PTA modes. Fuel Tank: Sets the fuel tank settings. Gauge Ranges: Configures the upper and lower limits and the range of desired standard operation of a gauge. Setting the Keel Offset You can enter a keel offset to compensate the surface reading for the depth of a keel, making it possible to measure depth from the bottom of the keel instead of from the transducer location. Enter a positive number to offset for a keel. You can enter a negative number to compensate for a large vessel that may draw several feet of water. Device Configuration 25