Garmin dezlCam 785 LMT-S Owners Manual - Page 34

4 Read the license agreements, and select Accept All to accept the agreements. NOTE: If you do not agree with the license terms, you can select Reject. This stops the update process. You cannot install updates until you accept the license agreements. 5 Using a USB cable, connect the device to external power, and select Continue (Charging the Device, page 27). For the best results, a USB wall charger that provides at least 1 A power output is recommended. Many USB power adapters for smartphones, tablets, or portable media devices may be compatible. 6 Keep the device connected to external power and within range of the Wi‑Fi network until the update process is complete. TIP: If a map update is interrupted or canceled before it completes, your device may be missing map data. To repair missing map data, you must update the maps again. Device Care NOTICE Avoid dropping your device. Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Never use a hard or sharp object to operate the touchscreen, or damage may result. Do not expose the device to water. Cleaning the Camera Lens NOTICE Do not use a dry cloth to clean the lens. Use of a dry cloth may damage the lens. Avoid chemical cleaners and solvents that can damage plastic components. You should clean the camera lens regularly to improve the quality of recorded video. 1 Wipe the lens with a soft, non-scratch cloth dampened with water or alcohol. 2 Allow the lens to air dry. Cleaning the Outer Casing NOTICE Avoid chemical cleaners and solvents that can damage plastic components. 1 Clean the outer casing of the device (not the touchscreen) using a cloth dampened with a mild detergent solution. 2 Wipe the device dry. Cleaning the Touchscreen 1 Use a soft, clean, lint-free cloth. 2 If necessary, lightly dampen the cloth with water. 3 If using a dampened cloth, turn off the device and disconnect the device from power. 4 Gently wipe the screen with the cloth. Avoiding Theft • Remove the device and mount from sight when not in use. • Remove the residue left on the windshield by the suction cup. • Do not keep your unit in the glove compartment. • Register your device using the Garmin Express software (garmin.com/express). Changing the Fuse in the Vehicle Power Cable NOTICE When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly. If your device does not charge in your vehicle, you may need to replace the fuse located at the tip of the vehicle adapter. 1 Rotate the end piece counter clockwise to unlock it. TIP: You may need to use a coin to remove the end piece. 2 Remove the end piece, the silver tip , and the fuse . 3 Insert a new fast-blow fuse that has the same current, such as 1 A or 2 A. 4 Place the silver tip in the end piece. 5 Push in the end piece and rotate it clockwise to lock it back into the vehicle power cable . Resetting the Device You can reset your device if it stops functioning. Hold the power key for 12 seconds. Removing the Device, Mount, and Suction Cup Removing the Mount from the Suction Cup 1 Turn the device mount to the right or left. 2 Apply pressure until the socket on the mount releases the ball on the suction cup. Removing the Suction Cup from the Windshield 1 Flip the lever on the suction cup toward you. 2 Pull the tab on the suction cup toward you. Troubleshooting The suction cup will not stay on my windshield 1 Clean the suction cup and windshield with rubbing alcohol. 2 Dry with a clean, dry cloth. 3 Mount the suction cup (Mounting and Powering the dēzlCam Device in Your Vehicle, page 1). The mount does not hold my device in place while I drive For the best results, you should keep the vehicle mount clean and position the device close to the suction cup. If the device shifts position while you are driving, you should complete these actions. • Remove the powered mount from the suction cup arm, and wipe the ball and socket with a cloth. Dust and other debris may reduce the friction in the ball and socket joint and allow the joint to shift while you are driving. • Rotate the hinged arm toward the suction cup as far as your windshield angle allows. 28 Troubleshooting