Gastroback 41403 User Manual - Page 19

Care and Cleaning

Get Gastroback 41403 PDF manuals and user guides View all Gastroback 41403 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Clearing a blocking - reverse operation CAUTION: Do not operate the motor in reverse direction for more than a few seconds. Reverse operation moves the foods to the motor housing. Thus, foods and juices could run into the gear hole of the motor housing. If the blockage of the worm shaft is not cleared away after a short moment of reverse operation, switch off the appliance via the ON/OFF button and power switch, then unplug and clean the appliance according to the instructions in chapter ›Care and Cleaning‹. Reverse operation is only intended for loosening blocked foods in the worm shaft by moving the worm shaft in opposite direction for a short moment. To activate reverse operation: 1.First switch off the motor via the ON/OFF button. Reverse operation is only available with the motor switched off and the power switch on. 2.Press and hold down the REVERSE button. The reverse operation starts immediately. In general, to release stuck food in the cutter housing, it is sufficient to operate the motor in reverse direction for just a moment. 3.You can switch off the reverse operation of the motor any time by releasing the button. If the motor gets stuck again or reverse operation does not work, switch off the appliance completely (ON/OFF button), unplug and clean the appliance according to the instructions in chapter ›Care and cleaning‹. However, if the problem persists, slow down working and cut your foods to smaller pieces, before processing in the mincer. Overheat protection This appliance is equipped with an overheat protection that will automatically shut off the appliance in case of overheating. If your appliance suddenly stops running act upon the instructions ›Power switch / overheat protection‹. Slow down your work-speed and use smaller portions. Regularly, switch off the appliance in between times for 15 minutes. Please contact you vendor or an authorized service centre, if the overheat protection is activated too often, anyhow. Care and Cleaning WARNING: Do not insert your hands or any foreign objects in the feed tube or outlet of the cutter housing, while the appliance is connected to the power supply. The cutter blade is sharp-edged. Handle with care to avoid cutting your fingers. Do not place or immerse the motor housing or power cord in water or any other liquids. Do not spill any liquids on the motor housing or power cord. Do not pour any liquids in the feed tube, while the cutter housing is assembled to the motor housing. Always disconnect the cutter housing from the motor housing, before assembling or disassembling any tools or removing stubborn blockages. Do not place the appliance or any part of it in an automatic dishwasher. 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
43
Clearing a blocking – reverse operation
CAUTION:
Do not operate the motor in reverse direction for more than a few seconds.
Reverse operation moves the foods to the motor housing. Thus, foods and juices could run
into the gear hole of the motor housing.
If the blockage of the worm shaft is not cleared away after a short moment of reverse ope-
ration, switch off the appliance via the ON/OFF button and power switch, then unplug and
clean the appliance according to the instructions in chapter ›Care and Cleaning‹.
Reverse operation is only intended for loosening blocked foods in the worm shaft by moving
the worm shaft in opposite direction for a short moment.
To activate reverse operation:
1.
First switch off the motor via the ON/OFF button. Reverse operation is only available with
the motor switched off and the power switch on.
2.
Press and hold down the REVERSE button. The reverse operation starts immediately. In
general, to release stuck food in the cutter housing, it is sufficient to operate the motor in
reverse direction for just a moment.
3.
You can switch off the reverse operation of the motor any time by releasing the button.
If the motor gets stuck again or reverse operation does not work, switch off the appliance
completely (ON/OFF button), unplug and clean the appliance according to the instructions
in chapter ›Care and cleaning‹. However, if the problem persists, slow down working and
cut your foods to smaller pieces, before processing in the mincer.
Overheat protection
This appliance is equipped with an overheat protection that will automatically shut off the
appliance in case of overheating.
If your appliance suddenly stops running act upon the instructions ›Power switch / overheat
protection‹.
Slow down your work-speed and use smaller portions. Regularly, switch off the appliance in
between times for 15 minutes. Please contact you vendor or an authorized service centre, if
the overheat protection is activated too often, anyhow.
Care and Cleaning
WARNING:
Do not insert your hands or any foreign objects in the feed tube or outlet of the
cutter housing, while the appliance is connected to the power supply.
The cutter blade is sharp-edged. Handle with care to avoid cutting your fingers.
Do not place or immerse the motor housing or power cord in water or any other liquids.
Do not spill any liquids on the motor housing or power cord. Do not pour any liquids in the
feed tube, while the cutter housing is assembled to the motor housing. Always disconnect
the cutter housing from the motor housing, before assembling or disassembling any tools or
removing stubborn blockages.
Do not place the appliance or any part of it in an automatic dishwasher.