Gateway GT5436E 8511861 - Gateway Computer Hardware Reference for Windows Vist - Page 45

Replacing the memory card, reader

Page 45 highlights

www.gateway.com Replacing the memory card reader Tools You need a Phillips screwdriver to replace the memory card reader. To replace the memory card reader: 1 Remove the side panel by following the instructions in "Removing the side panel" on page 31. 2 Remove the front bezel by following the instructions in "Removing the front bezel" on page 32. Important The color and shape of your replacement card reader's front cover may vary from your original card reader. 3 If you are installing a new card reader (not replacing an old one), remove the two drive retention screws in the drive bay, then go to Step 5. For the location of the screws, see the photo in Step 4. 4 Remove the two drive retention screws, disconnect the card reader's data cable from the system board, then slide the drive forward and out of the drive bay. Screws 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138

www.gateway.com
39
Replacing the memory card
reader
To replace the memory card reader:
1
Remove the side panel by following the instructions in
“Removing the side panel” on page 31
.
2
Remove the front bezel by following the instructions in
“Removing the front bezel” on page 32
.
3
If you are installing a new card reader (not replacing an
old one), remove the two drive retention screws in the
drive bay, then go to
Step 5
. For the location of the
screws, see the photo in
Step 4
.
4
Remove the two drive retention screws, disconnect the
card reader’s data cable from the system board, then
slide the drive forward and out of the drive bay.
Tools
You need a Phillips screwdriver to replace the memory card reader.
Important
The color and shape of your replacement card reader’s front
cover may vary from your original card reader.
Screws