GE CFE29TSDSS Installation Instructions - Page 30
Locating The Anti-tip Floor, Bracket Cont., Positioning The Refrigerator, To Engage The Anti-tip
View all GE CFE29TSDSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 30 highlights
Installation Instructions INSTALLING THE REFRIGERATOR (cont.) Anti-Tip Floor Bracket Installation (Models PYE, CYE, and PWE only) (cont.) AT-2 LOCATING THE ANTI-TIP FLOOR BRACKET (cont.) Figure 2 - Acceptable Screw Placement Locations Recommended Installation - Wood Recommended Installation - Concrete Minimum Acceptable #1 - Minimum Acceptable #2 - Wall Plate Stud Wood Floor B CONCRETE Wall and Floor Construction: $QFKRUVUHTXLUHGQRWSURYLGHG 4 each 1/4" (6 mm) x 1-1/2" (38 mm) lag bolts 4 each 1/2" (12 mm) O.D. sleeve anchors 'ULOOWKHUHFRPPHQGHGVL]HKROHVIRUWKH anchors into the concrete at the center of the holes marked in Step 2. ,QVWDOOWKHVOHHYHDQFKRUVLQWRWKHGULOOHG holes. Place the anti-tip floor bracket as indicated in Step 2. Remove the locator template from the floor. ,QVWDOOWKHODJEROWVWKURXJKWKHDQWLWLSIORRU bracket and tighten appropriately. C WOOD Wall and TILE Floor Construction: )RUWKLVVSHFLDOFDVHORFDWHWKHZDOOKROHV identified in Fig. 1. Drill an angled 1/8" (3 mm) pilot hole (approx. as shown in Fig. 3) in the center of each hole. 0RXQWWKHDQWLWLSIORRUEUDFNHWXVLQJWKH Minimum Acceptable Installation #1, as illustrated in Fig. 2. Minimum Acceptable #3 - Concrete Floor AT-3 ANTI-TIP BRACKET INSTALLATION A WOOD Wall and Floor Construction: 'ULOOWKHDSSURSULDWHQXPEHURIµPP pilot holes in the center of each floor bracket hole being used (a nail or awl may be used if a drill is not available) AND remove the locator template from the floor. Mount the anti-tip floor bracket by fastening the 2, or recommended 4, #10-16 hex-head screws tightly into place as illustrated in Figure 3. Figure 3 - Attachment to Wall and Floor Rear RH Corner of the Refrigerator 2 Screws Must Enter Wood or Metal Stud Floor Bracket Wall Wall Plate Stud Floor AT-4 POSITIONING THE REFRIGERATOR TO ENGAGE THE ANTI-TIP FLOOR AND BASE BRACKETS Before pushing the refrigerator into the A opening, plug the power cord into the receptacle and connect waterline (if equipped). Check for leaks. Locate the refrigerator's RH side and move back B approximately in line with the RH side of the cabinet opening, W. This should position the anti-tip floor bracket to engage the anti-tip base bracket on the refrigerator. Gently roll the refrigerator back into the cabinet C opening until it comes to a complete stop. Check to see if the refrigerator front lines up with the cabinet front face. If not, carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall. If Applicable: Adjust the rear (and front) wheel height settings to fully engage the rear anti-tip D brackets, while also aligning the refrigerator front with the cabinet front face. NOTE: If you pull the refrigerator out and away from the wall for any reason, make sure the anti-tip floor bracket is engaged when the refrigerator is pushed back against the rear wall. 30 Refer tp 239D1142 P001 Pub# 31-45484-2