GE JT3000SFSS Installation Instructions - Page 1
GE JT3000SFSS Manual
View all GE JT3000SFSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Installation Instructions 27" & 30" Electric Built-In Wall Ovens Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT - Save these instructions for local inspector's use. • IMPORTANT - Observe all governing codes and ordinances. • Note to Installer - Be sure to leave these instructions with Consumer. • Note to Consumer - Keep these instructions for future reference. • Skill level - Installation of this appliance requires a qualified installer or electrician. • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under Warranty. • Product is for indoor use only. ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. FOR YOUR SAFETY: WARNING: Before beginning the installation, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door. Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to 200°F [93.3°C]) generated by the oven. MATERIALS YOU MAY NEED Junction Box Wire Nuts Strain Relief Clamp for 1/2" Conduit TOOLS YOU MAY NEED 1/8" Drill Bit and Electric or Hand Drill Phillips Screwdriver Wire Strippers DESIGN INFORMATION SINGLE OVEN INSTALLATIONS The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also be installed below a countertop or below specified cooktops. See the label on top of the oven for approved models. DOUBLE OVEN INSTALLATIONS A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the oven for approved models. IMPORTANT: Always refer to individual installation instructions packed with each product for specific requirements. 2 PREPARE THE OPENING NOTE: If the cabinet does not have a solid bottom, two braces or runners must be installed to support the weight of the oven. For single ovens, the runners and braces must support 200 lbs (91 kg). For double ovens, the runners and braces must support 375 lbs. (170 kg). NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered. NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick, shim both sides equally to establish the cutout width. 2" x 4" (5 cm x 10 cm) or Equivalent Runners Level with Bottom of Cutout and Flush with Sides of Cutout CL Suitable Bracing to Support Runners 1 REMOVE PACKAGING MATERIALS Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks and heating elements. Remove protective film and labels on the outer door and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping screws securing the oven to the base pad. Open oven door and remove literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from seperate box and set aside (30" Double Wall Ovens Only).