GE NX548E Installation Instructions - Page 5
Transmitter options, Partition settings for keyfobs - wireless receiver
UPC - 782136713930
View all GE NX548E manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
5 Transmitter options LCD touchpads will display instructions when accomplishing tasks. To program the transmitter and partition settings, do the following: 1. Enter * 8 at the keypad. On LED touchpads, the five function lights start flashing. 2. Enter the program code (factory default is 9713). On LED touchpads, the service light flashes and the five function lights change from flashing to on steady. 3. Enter the DIP switch setting module number for the receiver and press #. On LED touchpads, the Armed LED turns on to indicate the control panel is waiting for a programming location entry. 4. Enter the zone location number and press #. On LED touchpads, the Armed LED turns on and the Zone LEDs display the binary data for the current settings. 5. Press the keypad button that corresponds to the feature number you want changed. On LED touchpads, the lights corresponding to the feature number will turn on or off depending on the previous state. On LCD touchpads, the feature number will turn on or off depending on the previous state. 6. Press * to enter the changes and automatically advance to segment 2. Note: If you press # instead of * in step 6, it exits the zone location and does not save changes to transmitter options. 7. Press # to exit zone location. To continue programming other zone locations, repeat steps 4 to7. To exit program mode, press EXIT EXIT. Door/window transmitter settings Use the following guidelines when setting features 4 and 5 (see Segment 1 in Table 5 on page 7) for door/window transmitters: • Feature 4 - Input option 1. Turn on this feature to disable the transmitter's internal reed switches. • Feature 5 - Input option 2. For transmitters that use a normally open (N/O) external contact, leave this feature off. For transmitters that use a normally closed (N/C) external contact, turn this feature on. Wireless smoke detector settings Use the following guideline when setting feature 4 (see Segment 1 in Table 5 on page 7) for wireless smoke detectors: • Feature 4 - Input option 1. For detectors with tamper switches, turn on this feature to enable the tamper feature. Note: Feature 4 must be off (disabled) when using wireless smoke detectors without tamper switches. 4-button keyfob settings The control panel installation manual describes how keyfob functions 1 and 2 can be used to control relays, outputs, or X-10 devices. Use the following guidelines when setting features 4 and 5 (see Segment 1 in Table 5 on page 7) for 4-button keyfobs: • Feature 4 - Input option 1. Turn on this feature to change the Light button to keyfob function 1. • Feature 5 - Input option 2. Turn on this feature to change the Star button to keyfob function 2. UFT settings Use the following guidelines when setting features 4, 5 and 7 (see Segment 1 in Table 5 on page 7) for UFTs: • Feature 4 - Input option 1. For UFTs, turn on this feature to disable the transmitter's primary reed. • Feature 5 - Input option 2. For UFTs on this feature to disable the transmitter's secondary reed. • Feature 7 - Input option 3. For UFTs that use a normally open (NO) external contact, leave this feature off. For UFTs that use a normally closed (NC) external contact, turn this feature on. Partition settings for keyfobs LCD touchpads will display instructions when accomplishing tasks. To program the transmitter and partition settings, do the following: 1. Enter * 8 at the keypad. On LED touchpads, the five function lights start flashing. 2. Enter the program code (factory default is 9 7 1 3). On LED touchpads, the service light flashes and the five function lights change from flashing to on steady. 3. Enter the DIP switch setting module number and press #. On LED touchpads, the Armed LED turns on to indicate the control panel is waiting for a programming location entry. 4. Enter the zone location number and press #. On LED touchpads, the Armed LED turns on and the Zone LEDs display the binary data for the current settings. On LCD touchpads, the display shows Segment 1 and its settings. 5. Press * to advance to Segment 2. 6. Press the keypad button that corresponds to the partition number you want to change. On LED touchpads, lights that turn off indicate the keyfob is active in that partition. On LCD touchpads, partition numbers that turn on indicate the keyfob is active in that partition. Note: These partition settings apply only to keyfobs. Partition assignments for other types of transmitters are made in the panel. 7. Press * to enter the changes. To continue programming transmitter partition settings, repeat steps 4 to 8. Note: If you press #, it does not save changes to the current segment, but it does save changes to previous segments. 8. To exit program mode, press EXIT EXIT.