Gigabyte GA-73VM-S2 Manual - Page 74

Making a SATA RAID/AHCI Driver Diskette - mcp73

Get Gigabyte GA-73VM-S2 PDF manuals and user guides View all Gigabyte GA-73VM-S2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

5-1-2 Making a SATA RAID/AHCI Driver Diskette (Required for AHCI and RAID Mode) To successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI mode, you need to install the SATA controller driver during the OS installation. Without the driver, the hard drive may not be recognized during the Windows setup process (Note 1) . First of all, copy the driver for the SATA controller from the motherboard driver disk to a floppy disk. For installing Windows Vista, you may directly load the SATA RAID driver from the motherboard driver disk during the OS installation process. For more details, refer to the next section, "5-1-3." See the instructions below about how to copy the driver in MS-DOS mode(Note 2). Prepare a startup disk that has CD-ROM support and a blank formatted floppy disk. Step 1: Insert the prepared startup disk and motherboard driver disk (e.g. the Windows XP driver disk) in your system. Boot from the startup disk. Once at the A:\> prompt, change to your optical drive (example: D:\>). At the D:\> prompt, type the following two commands. Press after each command (Figure 1): cd bootdrv menu Step 2: When the controller menu (Figure 2) appears, remove the startup disk and insert the blank formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For example, in the menu in Figure 2, to install Windows XP (32-bit) onto your RAID drives, press to select 2)NVIDIA MCP73 RAID DRIVER. Your system will then automatically zip and transfer this driver file to the floppy disk. Press to exit when finished. (Note 1) (Note 2) Figure 1 Figure 2 For AHCI drives, installation of Windows Vista does not require you to install the SATA AHCI driver in advance during the OS installation process. For users without a startup disk: Use an alternative system and insert the motherboard driver disk. From your optical drive folder, double click the MENU. exe file in the BootDrv folder (Figure 3).A command prompt window will open similar to that in Figure 2. GA-73VM-S2 Motherboard Figure 3 - 74 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
GA-73VM-S2 Motherboard
- 74 -
5-1-2
Making a SATA RAID/AHCI Driver Diskette
(Required for AHCI and RAID Mode)
To
successfully install operating system onto SATA hard drive(s) that is/are configured to RAID/AHCI
mode, you need to install the SATA controller driver during the OS installation. Without the driver, the
hard drive may not be recognized during the Windows setup process
(Note 1)
. First of all, copy the driver
for the SATA controller from the motherboard driver disk to a floppy disk. For installing Windows Vista,
you may directly load the SATA RAID driver from the motherboard driver disk during the OS installation
process. For more details, refer to the next section, "5-1-3." See the instructions below about how to
copy the driver in MS-DOS mode
(Note 2)
. Prepare a startup disk that has CD-ROM support and a blank
(Note 1)
For AHCI drives, installation of Windows Vista does not require you to install the SATA AHCI driver in advance during
the OS installation process.
(Note 2)
For users without a startup disk:
Use an alternative system and insert the motherboard driver disk. From your optical drive folder, double click the
MENU.
exe
file in the
BootDrv
folder (Figure 3).A command prompt window will open similar to that in Figure 2.
Figure 1
Figure 2
Figure 3
formatted floppy disk.
Step 1: Insert the prepared startup disk and motherboard driver disk (e.g. the Windows XP driver disk) in your
system. Boot from the startup disk. Once at the A:\> prompt, change to your optical drive (example: D:\>).
At the D:\> prompt, type the following two commands. Press <Enter> after each command (Figure 1):
cd bootdrv
menu
Step 2: When the controller menu (Figure 2) appears, remove the startup disk and insert the blank
formatted disk. Select the controller driver by pressing the corresponding letter from the menu. For
example, in the menu in Figure 2, to install Windows XP (32-bit) onto your RAID drives, press <2> to
select
2)NVIDIA MCP73 RAID DRIVER
. Your system will then automatically zip and transfer this
driver file to the floppy disk. Press <0> to exit when finished.