Gigabyte GN-AP03G User Manual - Page 24

Troubleshooting

Get Gigabyte GN-AP03G PDF manuals and user guides View all Gigabyte GN-AP03G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

GN-AP03G AirCruiser G Range Extender Chapter 4 Troubleshooting This chapter gives information about troubleshooting your AirCruiser G Range Extender. Read the descriptions below for assistance is diagnosing and solving the problem. Q: What to do if you forget your password or forget the IP address of the Range Extender? A: Please press and hold for 5 seconds the "init" button at the bottom of the Range Extender. The Access Point will be reset to the factory default values, and the password will be restored to factory default. Q: I am unable to connect to the Internet. A: 1. Confirm that the power cord is connected properly and the Range Extender's power LED is correctly lit. 2. Check whether all of the settings described in this manual are correctly set. 3. Verify that your ADSL/Cable Modem is operating normally, and/or you have ISP service available. 4. Check that your network cable is connected correctly, and the LED status is normal. Q: I am unable to access the Range Extender's Web Configuration Interface. A: 1. Please check the Ethernet connection (RJ-45 LAN cable) between the PC and the Range Extender is properly connected. 2. Make sure your computer's IP address is on the same subnet as the Range Extender. (Check this by typing "ipconfig /all" from a DOS command prompt) 3. Make sure you are carefully typing the correct IP address of the Range Extender in the address bar of your web browser. The IP address of your Range Extender is the "Gateway" address you see when you run the "ipconfig /all" command. 4. Try initializing your router to factory settings. Q: What is the IEEE 802.11b standard? A: It is also referred to as 802.11 High Rate or Wi-Fi. It is an expansion to 802.11 that applies to wireless LAN and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band. The 802.11b uses only Direct Sequence Spread Spectrum (DSSS). The 802.11b was a 1999 ratification to the origianl 802.11 standard, allowing wireless functionality comparable to Ethernet. Q: What is WEP? A: Wired Equivalent Privacy (WEP). A security mechanism defined within the 802.11 standard and designed to make the link integrity of the wireless medium equal to wired cable. Q: What is the IEEE 802.11g standard? A: IEEE 802.11g standard specifies data rates of up to 54 Mbps in the 2.45-GHz band. It uses Orthogonal Frequency Division Multiplexing (OFDM), which is the mandatory provisions have been made within the standard to make it inherently compatible with the well-established 802.11b standard at 11 Mbps, which uses Complementary Code Keying (CCK) modulation. Both .11g and .11b can operate at ranges of up to 300 feet. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
GN-AP03G AirCruiser G Range Extender
Chapter 4 Troubleshooting
This chapter gives information about troubleshooting your AirCruiser G Range Extender. Read the
descriptions below for assistance is diagnosing and solving the problem.
Q:
What to do if you forget your password or forget the IP address of the Range Extender?
A:
Please press and hold for 5 seconds the
“init”
button at the bottom of the Range Extender. The
Access Point will be reset to the factory default values, and the password will be restored to factory
default.
Q:
I am unable to connect to the Internet.
A:
1.
Confirm that the power cord is connected properly and the Range Extender’s power LED is
correctly lit.
2.
Check whether all of the settings described in this manual are correctly set.
3.
Verify that your ADSL/Cable Modem is operating normally, and/or you have ISP service
available.
4.
Check that your network cable is connected correctly, and the LED status is normal.
Q:
I am unable to access the Range Extender’s Web Configuration Interface.
A:
1.
Please check the Ethernet connection (RJ-45 LAN cable) between the PC and the Range
Extender is properly connected.
2.
Make sure your computer’s IP address is on the same subnet as the Range Extender. (Check
this by typing “
ipconfig /all”
from a DOS command prompt)
3.
Make sure you are carefully typing the correct IP address of the Range Extender in the address
bar of your web browser. The IP address of your Range Extender is the “Gateway” address you
see when you run the “
ipconfig /all”
command.
4.
Try initializing your router to factory settings.
Q:
What is the IEEE 802.11b standard?
A:
It is also referred to as 802.11 High Rate or Wi-Fi. It is an expansion to 802.11 that applies to wireless
LAN and provides 11 Mbps transmission (with a fallback to 5.5, 2 and 1 Mbps) in the 2.4 GHz band.
The 802.11b uses only Direct Sequence Spread Spectrum (DSSS). The 802.11b was a 1999
ratification to the origianl 802.11 standard, allowing wireless functionality comparable to Ethernet.
Q:
What is WEP?
A:
Wired Equivalent Privacy (WEP). A security mechanism defined within the 802.11 standard and
designed to make the link integrity of the wireless medium equal to wired cable.
Q:
What is the IEEE 802.11g standard?
A:
IEEE 802.11g standard specifies data rates of up to 54 Mbps in the 2.45-GHz band. It uses
Orthogonal Frequency Division Multiplexing (OFDM), which is the mandatory provisions have been
made within the standard to make it inherently compatible with the well-established 802.11b standard
at 11 Mbps, which uses Complementary Code Keying (CCK) modulation. Both .11g and .11b can
operate at ranges of up to 300 feet.
20