Haier HB21FC45NS User Manual - Page 34

from dirt and debris.

Get Haier HB21FC45NS PDF manuals and user guides View all Haier HB21FC45NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

English Problem Cause Solution Automatic icemaker The icemaker has stopped making ice. • The ice cube height sensor arm has detected a full tray condition. • The water supply valve is closed. • The freezer section is not cold enough. • To make more ice cubes you may need to distribute your ice to the center drawer right side (or lower drawer) to increase ice cube harvest volume. • Turn on the water supply valve. • Adjust the setting in the freezer to a colder setting and allow it to balance within 24 hours. • Check the water supply • The water source saddle saddles valve for obstruction valve is somehow blocked. and replace it if damaged. The ice making capacity is low. • The freezer drawer area is not cold enough. • The water supply valve does not have enough pressure or does not open all the way. • Set the freezer drawer to a colder setting. • Make sure the water pressure is between 25-121 psi and add water booster if too low. • Make sure the water valve supply is open all the way. • The icemaker sensor arm is restricted or out of position. • Make sure the water filter is distributing enough water and is not clogged. • Make sure the drawer gaskets are sealing and kept clean from dirt and debris. The icemaker runs continuously. • The icemaker level sensor is stuck in the down position. • Check the movement of the icemaker sensor arm so it rests in the "up" position. • Make sure no frozen packs or objects are obstructing the icemaker sensor arm. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
English
32
Problem
Cause
Solution
Automatic icemaker
The
icemaker
has stopped
making ice.
• The ice cube height sensor
arm has detected a full
tray condition.
• The water supply valve is
closed.
• The freezer section is not
cold enough.
• The water source saddle
valve is somehow blocked.
• To make more ice cubes you
may need to distribute your ice
to the center drawer right side
(or lower drawer) to increase
ice cube harvest volume.
• Turn on the water supply valve.
• Adjust the setting in the freezer
to a colder setting and allow it
to balance within 24 hours.
• Check the water supply
saddles valve for obstruction
and replace it if damaged.
The ice
making
capacity is
low.
• The freezer drawer area is
not cold enough.
• The water supply valve
does not have enough
pressure or does not open
all the way.
• The icemaker sensor arm
is restricted or out of
position.
• Set the freezer drawer to a
colder setting.
• Make sure the water pressure
is between 25-121 psi and
add water booster if too low.
• Make sure the water valve
supply is open all the way.
• Make sure the water filter is
distributing enough water and
is not clogged.
• Make sure the drawer gaskets
are sealing and kept clean
from dirt and debris.
The
icemaker
runs
continuously.
• The icemaker level sensor
is stuck in the down
position.
• Check the movement of the
icemaker sensor arm so it rests
in the “up” position.
• Make sure no frozen packs or
objects are obstructing the
icemaker sensor arm.