Haier HLPW028BXW Installation Instructions - Page 34

Operation, Water

Get Haier HLPW028BXW PDF manuals and user guides View all Haier HLPW028BXW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

ENGLISH ERROR CODE FA (Water Level Sensor Error) F2 (Water Level is Too High) DESCRIPTION The washer has detected water level sensor errors. The washer has detected higher than normal water levels, automatic draining has not resolved the issue. POSSIBLE CAUSE AND SOLUTION Call service center at 1-877-337-3639. Call service center at 1-877-337-3639. OPERATION PROBLEM Washer does not run POSSIBLE CAUSE(S) There is no electrical power going to the washer. Circuit breaker tripped or fuse blown The washer is overloaded or the wash load is not balanced. The Heavy Duty or Whites cycle was selected. Delay start has been selected. The washer lid is open. SOLUTION Plug the power cord into a grounded 3 prong outlet. Reset/Turn on circuit breaker or replace fuse. Laundry may need to be removed or redistributed to rebalance the load. The washer pauses during cycles for the laundry to soak. When the soak time ends, the washer will restart automatically. Cancel the delay start. Close the washer lid. WATER PROBLEM Water flow is slow or filling takes a long time Water temperature is too warm or cold POSSIBLE CAUSE(S) Hose filter screens on the water inlet valves may be clogged. Water inlet faucets are not fully turned on. Water fill hose is kinked. There is no water supply to the house or the water pressure is too low. Water heater temperature is not set correctly. SOLUTION Disconnect hoses from inlet valves and clean the screens. Make sure that the water faucets are fully turned on. Make sure the water hoses are not tangled, kinked, or pinched. Check another faucet in the house to make sure that household water pressure is adequate. Hot water needs to be at a temperature of at least 120°F -140°F (49°C - 60°C). 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
ERROR CODE
DESCRIPTION
POSSIBLE CAUSE AND
SOLUTION
FA
(Water Level
Sensor Error)
The washer has detected
water level sensor errors.
Call service center at
1-877-337-3639.
F2
(Water Level is
Too High)
The washer has detected
higher than normal water
levels, automatic draining
has not resolved the issue.
Call service center at
1-877-337-3639.
OPERATION
PROBLEM
POSSIBLE CAUSE(S)
SOLUTION
Washer does
not run
There is no electrical power
going to the washer.
Plug the power cord into a
grounded 3 prong outlet.
Circuit breaker tripped or
fuse blown
Reset/Turn on circuit breaker
or replace fuse.
The washer is overloaded or
the wash load is not
balanced.
Laundry may need to be
removed or redistributed to
rebalance the load.
The Heavy Duty or Whites
cycle was selected.
The washer pauses during
cycles for the laundry to soak.
When the soak time ends, the
washer will restart
automatically.
Delay start has been
selected.
Cancel the delay start.
The washer lid is open.
Close the washer lid.
WATER
PROBLEM
POSSIBLE CAUSE(S)
SOLUTION
Water flow is
slow or filling
takes a long
time
Hose filter screens on the
water inlet valves may be
clogged.
Disconnect hoses from inlet
valves and clean the screens.
Water inlet faucets are not
fully turned on.
Make sure that the water
faucets are fully turned on.
Water fill hose is kinked.
Make sure the water hoses are
not tangled, kinked, or
pinched.
There is no water supply to
the house or the water
pressure is too low.
Check another faucet in the
house to make sure that
household water pressure is
adequate.
Water
temperature is
too warm or
cold
Water heater temperature
is not set correctly.
Hot water needs to be at a
temperature of at least 120°F
-140°F (49°C - 60°C).
32
ENGLISH