Haier HMV1630DBBB HMV1630 Installation Guide - Page 18

B. Outside Back Exhaust

Get Haier HMV1630DBBB PDF manuals and user guides View all Haier HMV1630DBBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Engglliisshh B. OUTSIDE BACK EXHAUST (HORIZONTAL DUCT) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven IMPORTANT NOTES: t Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration t Make sure the motor wiring has been properly routed and secured, and that the wires are not pinched. B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST You need to cut an opening in the rear wall for outside exhaust. t Read the instructions on the REAR WALL TEMPLATE. t Tape it to the rear wall, lining up with the holes previously drilled for holes A and B in the wall plate. t Cut the opening, following the instructions of the REAR WALL TEMPLATE. B2. REMOVE BLOWER PLATE Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate. Blower Plate Back of Microwave 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
17
English
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
You need to cut an opening in the rear
wall for outside exhaust.
Read the instructions on the REAR
WALL TEMPLATE.
Tape it to the rear wall, lining up with
the holes previously drilled for holes A
and B in the wall plate.
Cut the opening, following the
instructions of the REAR WALL
TEMPLATE.
Remove and save the screw that holds the
blower plate to the microwave. Lift off the
blower plate.
B1. PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST
B2. REMOVE BLOWER PLATE
B. OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
Back of
Microwave
Blower Plate
IMPORTANT NOTES:
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help to prevent excessive vibration
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.