Haier HMV1630DBBB HMV1630 Installation Guide - Page 24

C2. Use Top Cabinet Template For Preparation Of, Top Cabinet, C3. Check Blower Plate, C4. Mount

Get Haier HMV1630DBBB PDF manuals and user guides View all Haier HMV1630DBBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

English C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through. t Read the instructions on the TOP CABINET TEMPLATE. t Tape it underneath the top cabinet. t Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. C3. CHECK BLOWER PLATE t Place the microwave in its upright position, with the top of the unit facing up. t Check to see that the blower plate is correctly installed on the unit. C4. MOUNT THE MICROWAVE OVEN Blower Plate FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf. IMPORTANT: If filler blocks are not used, case damage may occur from overtightening screws. 1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. 2. Rotate front of oven up against cabinet bottom. NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1-3. Do not pinch cord or lift oven by pulling cord. 1 2 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
English
You need to drill holes for the top support
screws, a hole large enough for the power
cord to fit through.
Read the instructions on the TOP
CABINET TEMPLATE.
Tape it underneath the top cabinet.
Drill the holes, following the instructions
on the TOP CABINET TEMPLATE.
Place the microwave in its upright
position, with the top of the unit facing up.
Check to see that the blower plate is
correctly installed on the unit.
C2. USE TOP CABINET TEMPLATE FOR PREPARATION OF
TOP CABINET
C3. CHECK BLOWER PLATE
Blower Plate
C4. MOUNT THE MICROWAVE OVEN
Lift microwave, tilt it forward, and hook slots
1.
at back bottom edge onto four lower tabs of
mounting plate.
Rotate front of oven up against cabinet
2.
bottom.
NOTE: When mounting the
microwave oven, thread power
cord through hole in bottom
of top cabinet. Keep it tight
throughout Steps 1–3. Do
not pinch cord or lift oven by
pulling cord.
1
2
23
CAUTION:
Wear safety goggles when drilling holes in the cabinet bottom.
FOR EASIER INSTALLATION
AND PERSONAL SAFETY, WE
RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your cabinet is metal, use the
nylon grommet around the power cord
hole to prevent cutting of the cord.
NOTE: We recommend using filler
blocks if the cabinet front hangs below
the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from
overtightening screws.