Haier HWM65-828 User Manual - Page 7

WASH SPIN D "WASH" button Press the "WASH" button to select wash procedure. Press the "WASH "button, the light flashes then press SET "+ - " to select the desired wash time from the STANDARD, HEAVY, CHILD, MEMORY programs 0-25mins . Press SET "+ - " button can change the process ,can not change time from the GENTLE and WOOL programs. The button is unavailable from the SPEEDY and TUB DRY programs. E "SPIN"button Press the "SPIN "button to select spin procedure. Press the "SPIN "button, the light flashes then press SET "+ - " to select the desired spin time from the STANDARD ,HEAVY ,CHILD ,MEMORY programs 0-9mins . The button is unavailable from the SPEEDY and TUB DRY programs. Press "SPIN"button ,then press SET "+ - " button can change the process,can not change time from the GENTLE and WOOL programs. F "WATER LEVEL"button WATER LEVEL The washing machine can detect the laundries automatically. After detection, it will set the water level to suitable value among 4, 6, 8,10 and 12 automatically. During the STANDARD program,You can also set water level by yourself. After the machine is started, it will not set water level automatically. You shall push the "START/PAUSE " button to make new setting. If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .If wet laundries are put in, it may display water level 12. You must set suitable water level by yourself. During operation of SOAK,WASH and RINSE programs, you can push down the WATER LEVEL button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water. The water level decided may be different from actual value because of the different moisture level of the laundries. If SPEEDY program is selected, it will display water level 3 . It will display water level 4 when it rinses. When STANDARD ,MEMORY ,HEAVY ,CHILD and GENTLE programs the rinse water value will be one level higher than the wash water value.(Except 12 water value and when the rinse water value is selected by yourself). Under the wool program, only the 6 to12 water level can be selected. AIR DRY G G" D"ARIYRINDGR"Y"bbuuttoonn Push the "AIR DRY" button to select air dry procedure. The program is chosen(0.5h, 1.0h,2.0h). It can dry the inner tub and the outer tub when 0.5h,1.0h are selected , which can avoid growing mildew on the outer tub and the inner tub. 2.0h can dry laundries ,the max drying capacity of the fibre laundries is 1.5 kg. "AIR DRY"program can not be reserved. RINSE H "RINSE" button Press the "RINSE "button to select rinse procedure. Press the "RINSE "button, the light flashes then press SET "+ - " to select the desired rinse times from the STANDARD ,HEAVY ,CHILD ,MEMORY programs (0.1.2.3). For GENTLE ,WOOL programs, press "RINSE"button , then press SET "+ - " button can change the process ,can not change time. The button is unavailable from the SPEEDY and TUB DRY programs. 12 Adjust the Installation position The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in unstable running or stoppage of the machine. Please adjust it with following methods: Confirm it's horizontal: Hang the lead line to check if it is horizontal. Adjust the adjustable foot: 1 .To twist the adjustable leg, please first lift up the side of the foot slightly, loosen the adjustable nut, and twist the foot. 2 . After adjustment, fasten the nut. Loosen High the adjustable nut Fasten the adjustable foot Low Usage of the drain hose The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way. 2.Do not step on or press the drain hose. 4.If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m. > 30mm