Haier HWM80-0566 User Manual - Page 4

Safety precautions Please plug the power plug on special receptacle. Be sure to use three-pins power receptacle. Ensure that the earthing prong of the power receptacle is earthed reliably. Use leakage protector if possible. The washing machine must be positioned so that the plug is accessible. Be sure to pull the plug off and close the water faucet in following cases: power failure, delivering the machine, setting the machine idle or cleaning the machine. Do not plug or pull the power plug with wet hand. Do not bend ,extend, twist, bind by force. Do not press or nip it with weight. Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with dry cloth carefully. If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by the technicians of our special shop or the after-sale service department. In case the washing machine is installed on ground with carpet, do not block the ventilation hole with carpet. The ventilation holes at the bottom Back Soft object Front Do not use water hotter than 50 . Do not put the machine at damp place like the bathroom. Never wash it with water. Do not put wet laundries on the control panel. Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning. Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more. 2 Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomena The digitron displays E0. The drainage cannot work, or is too slow. The digitron displays E1. It stops running in midway. The digitron displays E2. The safety switch acts, and the spinning cannot work. The digitron displays E3. The water filling does not work, or is slow. After about 15 minutes later, the digital displays E4. The digitron displays E6. The machine does not act Not wash Not spin The reason How to settle The top lid is opened during reserve procedure. Is the drain hose put down? Is the drain hose blocked? The top lid is not closed. Close the top lid. Put down the drain hose. Open and close the top lid once. Clean the foreign material. Open and close the top lid once. Close the top lid. Are the laundries put slantingly? Is the machine slanting? Is the water tap opened, or is there water supply failure? Is the water inlet valve blocked? Is the water pressure too low? The water level sensor is bad. Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position? Reorder the laundries. Close the top lid. Th machine will start running after 10 seconds of being placed horizontally. Open the water tap. Push the start/Pause button once. Clean the water inlet valve then push the start/Pause button once. Push the Start/Pause button once. Please contact the after-sales service department. Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position. Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat? Insert the power plug tightly. Close the top lid. Set the laundries flat. There's abnormal sound inside the machine Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials? Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials. The water tap leaks Is the screw of the jointer of water inlet hose loose or awry? Fasten the screw of the jointer properly. Common phenomena Phenomena Explanation The spinning is intermittent when it starts. The wash procedure is paused. Push the PROGRAM button to select SPIN, but it doesn't work. The pulsator pauses during water inlet in wash and rinse. There may be some water flowing out of the drain hose in the first use of the machine. Balance the laundries to avoid slanting. The cloth sensor is checking the cloth, it will add water after 48 seconds. The program is setting the drain time. Some time is needed before it starts spinning. It is to avoid splashing during water inlet. It is the water remained in the factory inspection of performance.