Hamilton Beach 53603 Use and Care Manual - Page 12

Troubleshooting

Get Hamilton Beach 53603 PDF manuals and user guides View all Hamilton Beach 53603 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Troubleshooting All program buttons are flashing. • The motor is not rotating and is experiencing a locked rotor condition. Turn power switch to OFF ( ) and remove the blender jar. Turn power switch to ON (I), run blender without jar in place on HI for 30 seconds to 1 minute, and resume normal operation. NOTE: Buttons start flashing 2-3 seconds after a problem has occurred. Blender fails to start. • Make sure main power ON(I)/OFF( ) switch is in the ON (I) position. • Check to see if unit is securely plugged into an electrical outlet of proper voltage and frequency. • Check to see if fuse for electrical outlet has blown or if a circuit breaker has tripped. Ingredients will not mix properly. • Check to see if enough liquid has been added to ingredients. Mixture should be fluid and free-running at all times. • Solid pieces are too large. • Container is too full. Do not fill past highest (6.5 cups/1.5 L) graduation marking. • Cutting blade assembly blades are not sharp or are damaged. Inspect container and cutting blade assembly daily. • Select speed to create a fluid blend. Blender smells like it is burning. • Turn off blender and allow unit to cool. • Although motors are tested during the manufacturing process, heavy use may cause curing of motor windings. The smell may quickly dissipate after a few heavy uses. • If smell continues after additional heavy uses, call our customer care center. There is grease around bottom of blender jar or on counter top. • Monitor problem and source. This may indicate an issue with jar bearings. • Call our customer care center if condition persists. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
Troubleshooting
All program buttons are flashing.
•
The motor is not rotating and is experiencing a locked rotor
condition. Turn power switch to OFF (
) and remove the blender
jar. Turn power switch to ON (
I
), run blender without jar in place
on HI for 30 seconds to 1 minute, and resume normal operation.
NOTE:
Buttons start flashing 2–3 seconds after a problem has
occurred.
Blender fails to start.
• Make sure main power ON(
I
)/OFF(
) switch is in the ON (
I
)
position.
•
Check to see if unit is securely plugged into an electrical outlet of
proper voltage and frequency.
•
Check to see if fuse for electrical outlet has blown or if a circuit
breaker has tripped.
Ingredients will not mix properly.
•
Check to see if enough liquid has been added to ingredients.
Mixture should be fluid and free-running at all times.
• Solid pieces are too large.
•
Container is too full. Do not fill past highest (6.5 cups/1.5 L)
graduation marking.
•
Cutting blade assembly blades are not sharp or are damaged.
Inspect container and cutting blade assembly daily.
•
Select speed to create a fluid blend.
Blender smells like it is burning.
•
Turn off blender and allow unit to cool.
•
Although motors are tested during the manufacturing process,
heavy use may cause curing of motor windings. The smell may
quickly dissipate after a few heavy uses.
•
If smell continues after additional heavy uses, call our customer
care center.
There is grease around bottom of blender jar or on counter top.
•
Monitor problem and source. This may indicate an issue with jar
bearings.
•
Call our customer care center if condition persists.