Hayward OnCommand Model: ALL MODELS Operation - Page 11

Adjust the desired low speed for variable speed operation, Move to previous/next menu item - parts

Get Hayward OnCommand PDF manuals and user guides View all Hayward OnCommand manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Pool Low Speed 50% Adjust the desired low speed for variable speed operation Move to previous/next menu item This setting will appear if "spa only" is not selected and variable speed filter pump is enabled. This setting determines the speed of the pump during low speed pool or spillover operation. This value can be set from "Lowest Speed" to 50% in 5% increments. 50% is default. Set Day and Time Wednesday 1100::3377PP Set Day and Time Wednesday 37 Set Day and Time Wednesday 10: P Adjust the current day of the week Move to hours setting Adjust the current hour (including AM/PM if applicable) Move to minutes setting Adjust the current minute Move to previous/next menu item Use this function to set the current day of the week and time. These values are used for all the automatic timeclock functions of the OnCommand and are also displayed as part of the default menu. The OnCommand is designed to keep the clock running during power outages lasting less than 7 days. If power has been off for longer than 7 days, then the time may have to be reset. Display Light On for 60 sec Toggle between Always On and On for 60 sec. Move to previous/next menu item This function controls the backlight on the display. If the "60 seconds" option is selected, then the backlight will automatically turn off 60 seconds after the last key is pressed and will stay off until next time a key is pressed. Note that the Display Light selection only applies to the display keypad that you are currently using. Other display/keypads will not be affected. In other words, you need to individually set this option for each display/keypad in the system. Beeper Enabled Toggle between Enabled (default) and Disabled Beeper Move to next menu item When "Enabled", the keypad will beep every time a key is pressed. If this audible indication is not desired, select "Disabled". This function only applies to the display/keypad that you are currently using. You need to set this option for each display/keypad in your system. NOTE: This function is not supported on all display/keypads. If the "Enabled" selection is not blinking, then the current software revision of that particular keypad/display does not support the option and it will default to Beeper Enabled. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
Pool Low Speed
50%
Adjust the desired low speed for variable speed operation
Move to previous/next menu item
This setting will appear if “spa only” is
not selected and variable speed filter pump is enabled.
This
setting determines the speed of the pump during low speed pool or spillover operation.
This value
can be set from “Lowest Speed” to 50% in 5% increments. 50% is default.
Set Day and Time
Wednesday 10:37P
Adjust the current day of the week
Move to hours setting
Set Day and Time
10:37P
Set Day and Time
Wednesday
37
Set Day and Time
Wednesday 10:
P
Adjust the current hour (including AM/PM if applicable)
Adjust the current minute
Move to minutes setting
Move to previous/next menu item
Use this function to set the current day of the week and time.
These values are used for all the
automatic timeclock functions of the OnCommand and are also displayed as part of the default menu.
The OnCommand is designed to keep the clock running during power outages lasting less than 7
days.
If power has been off for longer than 7 days, then the time may have to be reset.
Display Light
On for 60 sec
Toggle between Always On and On for 60 sec.
Move to previous/next menu item
This function controls the backlight on the display.
If the “60 seconds” option is selected, then the
backlight will automatically turn off 60 seconds after the last key is pressed and will stay off until next
time a key is pressed.
Note that the Display Light selection only applies to the display keypad that you are currently using.
Other display/keypads will not be affected.
In other words, you need to individually set this option
for each display/keypad in the system.
Beeper
Enabled
Toggle between Enabled (default) and Disabled Beeper
Move to next menu item
When “Enabled”, the keypad will beep every time a key is pressed.
If this audible indication is not
desired, select “Disabled”.
This function only applies to the display/keypad that you are currently using.
You need to set this
option for each display/keypad in your system.
NOTE: This function is not supported on all display/keypads.
If the “Enabled” selection is not
blinking, then the current software revision of that particular keypad/display does not support the
option and it will default to Beeper Enabled.