Hayward Power-Flo Model: ALL - Page 7

Storage/Winterization, Start-Up For Winterized Equipment, Shaft Seal Change Instructions, SAVE THESE - pump

Get Hayward Power-Flo PDF manuals and user guides View all Hayward Power-Flo manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Power-Flo LX™ / Power-Flo II™ Pump Series Storage/Winterization WARNING - Explosion Hazard. Purging the system with compressed air can cause components to explode, with risk of severe injury or death to anyone nearby. Use only a low pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping. CAUTION - Allowing the pump to freeze will void the warranty. CAUTION - Do NOT use anti-freeze solutions (except propylene glycol) in your pool/spa system. Propylene glycol is non-toxic and will not damage plastic system components; other antifreezes are highly toxic and may damage plastic components in the system. Drain all water from pump and piping when expecting freezing temperatures or when storing pump for a long time (see instructions below). Gravity drain system as far as possible. Keep motor dry and covered during storage. To avoid condensation/corrosion problems, do NOT cover or wrap pump with plastic film or bags. Storing Pump For Winterization WARNING - To avoid dangerous or fatal electrical shock hazard, turn OFF power to motor before draining pump. 1. Drain water level below all inlets to the pool. 2. Remove drain plug from bottom of strainer body. 3. Disconnect pump from base. 4. Once the pump is removed of water, re-install the strainer lid and strainer plug. 5. Store pump in a dry enclosure. Start-Up For Winterized Equipment 1. Follow filter manufacturer's instructions for reactivation of the filter. 2. Inspect all electrical wiring for damage or deterioration over the shutdown period. Have a qualified serviceman repair/replace wiring as needed. 3. Securely mount pump to base. 4. Install all intake and output fittings and piping. 5. Refill pool to proper water level. 6. Prime pump according to instructions. Shaft Seal Change Instructions IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND FOLLOW ALL INSTRUCTIONS When servicing electrical equipment, basic safety precautions should always be observed including the following. Failure to follow instructions may result in injury. A. WARNING - To reduce risk of injury, do not permit children to use this product. B. Disconnect all electrical power service to pump before beginning shaft seal replacement. C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward Dealer or service center if you have any questions. D. The National Electrical Code requires either a three (3) foot maximum twist-lock cord set with a GFCI protected receptacle or hard wire (conduit) connection for swimming pool pump installation. Do not use extension cords. SAVE THESE INSTRUCTIONS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
Power-Flo
LX™ / Power-Flo II™ Pump Series
___________________________________________
Storage/Winterization
WARNING
–
Explosion Hazard.
Purging the system with compressed air can cause
components to explode, with risk of severe injury or death to anyone nearby.
Use only a low
pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping.
CAUTION
–
Allowing the pump to freeze will void the warranty.
CAUTION
–
Do NOT use anti-freeze solutions (except propylene glycol) in your pool/spa
system.
Propylene glycol is non-toxic and will not damage plastic system components; other anti-
freezes are highly toxic and may damage plastic components in the system.
Drain all water from pump and piping when expecting freezing temperatures or when storing pump for a long time
(see instructions below).
Gravity drain system as far as possible.
Keep motor dry and covered during storage.
To avoid condensation/corrosion problems, do NOT cover or wrap pump
with plastic film or bags.
Storing Pump For Winterization
WARNING
–
To avoid dangerous or fatal electrical shock hazard, turn OFF power to motor
before draining pump.
1.
Drain water level below all inlets to the pool.
2.
Remove drain plug from bottom of strainer body.
3.
Disconnect pump from base.
4.
Once the pump is removed of water, re-install the strainer lid and strainer plug.
5.
Store pump in a dry enclosure.
Start-Up For Winterized Equipment
1.
Follow filter manufacturer's instructions for reactivation of the filter.
2.
Inspect all electrical wiring for damage or deterioration over the shutdown period.
Have a qualified
serviceman repair/replace wiring as needed.
3.
Securely mount pump to base.
4.
Install all intake and output fittings and piping.
5.
Refill pool to proper water level.
6.
Prime pump according to instructions.
Shaft Seal Change Instructions
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND FOLLOW ALL INSTRUCTIONS
When servicing electrical equipment, basic safety precautions should always be observed including the following.
Failure to
follow instructions may result in injury.
A.
WARNING
–
To reduce risk of injury, do not permit children to use this product.
B.
Disconnect all electrical power service to pump before beginning shaft seal replacement.
C.
Only qualified personnel should attempt rotary seal replacement.
Contact your local authorized Hayward
Dealer or service center if you have any questions.
D.
The National Electrical Code requires either a three (3) foot maximum twist-lock cord set with a GFCI
protected receptacle or hard wire (conduit) connection for swimming pool pump installation.
Do not use
extension cords.
SAVE THESE INSTRUCTIONS