Hayward PowerFlo Matrix Models: SP1591 SP1592 SP15922S SP1592FT SP1592FTTL - Page 9

Shaft Seal Change Instructions cont., Troubleshooting

Get Hayward PowerFlo Matrix PDF manuals and user guides View all Hayward PowerFlo Matrix manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Power-Flo Matrix™ Pump Series Shaft Seal Change Instructions (cont.) 5. Hold the motor shaft securely by either inserting a screwdriver in slot at end of shaft or by using an open-end wrench to engage the flat surfaces provided near end of motor shaft. Rotate the impeller ina a counterclockwise direction and remove it from the motor shaft. 6. Note how the steel spring section of the old seal is positioned on impeller hub and remove it by pulling from the impeller. 7. Loosen four (4) motor through bolts from the back of motor and remove pump housing/shroud from the front of the motor. 8. Remove the ceramic stationary portion of the old seal by pressing the white ceramic seat out of the pump housing recess. If assembly is tight, tap lightly from the "motor" side. 9. Clean and lubricate the impeller stem and the pump housing recess with a dilute solution of non-granulated liquid-type soap. Do not use petroleum or silicone lubricants as these can contribute to seal leakage. 10. Press the new rotating portion of the seal assembly onto the impeller stem with the polished black graphite surface facing away from the impeller. 11. Carefully press the stationary ceramic portion of the seal into the recess of the pump housing/shroud, with the polished flat surface facing out. 12. Carefully insert the motor shaft through the pump housing/shroud and align with white ceramic stationary seal assembly in place and secure the motor to pump housing/shroud with four (4) motor through bolts removed in step #7. Be sure motor base and pump discharge port are positioned properly. Alternately tighten the motor through bolts until the pump housing is secure. Make certain motor shaft turns freely before proceeding. 13. Screw the impeller (clockwise) with the rotating portion of seal in place onto the motor shaft. Hand-tighten the impeller in place. 14. Clean (replace if necessary) the O-ring and replace on pump cover. Assemble the pump cover to the pump housing/ shroud with the eight (8) screws removed in step #3. Tighten screws alternately and evenly. 15. Re-assemble strainer by sliding strainer housing onto pump cover. Install strainer 'C' clip by pushing clip down onto grooved pump cover coupling. Insert basket and fasten strainer cover. 16. Reconnect pump to the piping or hoses provided. Open all valves and make sure that the pump strainer housing is full of water before restarting the pump. Troubleshooting Motor Will NOT Start - Check For: 1. Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI's, or blown fuses. 2. Manually check rotation of motor shaft for free movement and lack of obstruction. (See steps 4 & 5 of "Shaft Seal Change Instructions" in this manual.) 3. If you have a timer, be certain it is working properly. Bypass it if necessary. Motor Shuts OFF - Check For: 1. Undersized wiring; loose connections; etc. 2. Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use). 3. Mechanical binding and electrical overload. NOTE: Your Hayward pump motor is equipped with an "automatic thermal overload protector." The motor will automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The "thermal overload protector" will allow the motor to automatically restart once the motor has cooled, provided the power source is again up to proper levels. It will continue to cut On/Off until the problem is corrected. Be sure to correct cause of overheating. Motor Hums, But Does NOT Start - Check For: 1. Centrifugal switch stuck in OPEN position. 2. Binding of motor shaft.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
Power-Flo Matrix
™
Pump Series
____________________
Shaft Seal Change Instructions (cont.)
5.
Hold the motor shaft securely by either inserting a screwdriver in slot at end of shaft or by using an open-end wrench
to engage the flat surfaces provided near end of motor shaft.
Rotate the impeller ina a counterclockwise direction and
remove it from the motor shaft.
6.
Note how the steel spring section of the old seal is positioned on impeller hub and remove it by pulling from the
impeller.
7.
Loosen four (4) motor through bolts from the back of motor and remove pump housing/shroud from the front of the
motor.
8.
Remove the ceramic stationary portion of the old seal by pressing the white ceramic seat out of the pump housing
recess.
If assembly is tight, tap lightly from the “motor” side.
9.
Clean and lubricate the impeller stem and the pump housing recess with a dilute solution of non-granulated liquid-type
soap.
Do not use petroleum or silicone lubricants as these can contribute to seal leakage.
10.
Press the new rotating portion of the seal assembly onto the impeller stem with the polished black graphite surface
facing away from the impeller.
11.
Carefully press the stationary ceramic portion of the seal into the recess of the pump housing/shroud, with the polished
flat surface facing out.
12.
Carefully insert the motor shaft through the pump housing/shroud and align with white ceramic stationary seal
assembly in place and secure the motor to pump housing/shroud with four (4) motor through bolts removed in step #7.
Be sure motor base and pump discharge port are positioned properly.
Alternately tighten the motor through bolts until
the pump housing is secure.
Make certain motor shaft turns freely before proceeding.
13.
Screw the impeller (clockwise) with the rotating portion of seal in place onto the motor shaft.
Hand-tighten the
impeller in place.
14.
Clean (replace if necessary) the O-ring and replace on pump cover.
Assemble the pump cover to the pump housing/
shroud with the eight (8) screws removed in step #3.
Tighten screws alternately and evenly.
15.
Re-assemble strainer by sliding strainer housing onto pump cover.
Install strainer ‘C’ clip by pushing clip down onto
grooved pump cover coupling.
Insert basket and fasten strainer cover.
16.
Reconnect pump to the piping or hoses provided.
Open all valves and make sure that the pump strainer housing is full
of water before restarting the pump.
Troubleshooting
Motor Will NOT Start – Check For:
1.
Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown fuses.
2.
Manually check rotation of motor shaft for free movement and lack of obstruction.
(See steps 4 & 5 of “Shaft
Seal Change Instructions” in this manual.)
3.
If you have a timer, be certain it is working properly.
Bypass it if necessary.
Motor Shuts OFF – Check For:
1.
Undersized wiring; loose connections; etc.
2.
Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use).
3.
Mechanical binding and electrical overload.
NOTE:
Your Hayward pump motor is equipped with an “automatic thermal overload protector.”
The motor will
automatically shut off if power supply drops before heat damage can build up causing windings to burn out.
The
“thermal overload protector” will allow the motor to automatically restart once the motor has cooled, provided the
power source is again up to proper levels.
It will continue to cut On/Off until the problem is corrected.
Be sure to
correct cause of overheating.
Motor Hums, But Does NOT Start – Check For:
1.
Centrifugal switch stuck in OPEN position.
2.
Binding of motor shaft.