Hayward Pro Logic Model: PL-P-4 Operation - Page 15

Maintenance Menu (only displays if Sensing System is enabled) The Maintenance Menu will be displayed only if the optional AQL-CHEM is used and the Sensing System is enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP and pH sensing kit. pH Calibration Wizard, + to enter Push to access pH Calibration Wizard Move to previous/next menu item Use this Wizard to calibrate the AQL-CHEM's pH probe. This requires a manual pH test of the pool water using a dependable red phenol test kit. Clean Probe Wizard + to enter Push to access Clean Probe Wizard Move to previous/next menu item Use this Wizard to clean the AQL-CHEM's ORP and pH probes. The probes must be clean and free from oil, chemical deposits and contamination to function properly. Slow response, increased need to calibrate, and inconsistent readings are indications that the probes need to be cleaned. 23 Set DSapyaa-nadll Time W6ed:0n0ePsdtaoy 91:00:03P7P or Spa-wkend 6:00P to 9:00P Adjust time setting Move between start and stop times & to previous/next menu item Adjust time setting Move between start and stop times & to previous/next menu item Spa-wkday 6:00P to 9:00P Adjust time setting Move between start and stop times & to previous/next menu item This menu is only available if the system has been setup for "pool and spa". During the programmed spa time, the Pro Logic will turn on the filter pump and move the pool/spa valves into the "spa-only" position. The heater will automatically heat the spa up to the programmed spa temperature (page 7). This programmed spa operation will take precedence over all other automatic functions, only manual operation of the filter button or pool/spa valve button will override this function. If your pool has a separate jet pump or blower controlled by Aux1 and/or Aux2 , you will have to program those separately. Set LDigahytasn-dallTime W8e:d0n0ePsdtoay1110:0:307PP or Lights-wkend 8:00P to 11:00P Adjust time setting Move between start and stop times & to previous/next menu item Adjust time setting Move between start and stop times & to previous/next menu item Lights-wkday Adjust time setting 8:00P to 11:00P Move between start and stop times & to previous/next menu item This menu will appear only if the Lights are configured for timeclock. The lights will turn on and off at or the designated times. The only override on this function is manual on/off control by the "Lights" button. Lights-CountDn 0:20 Adjust time setting (Manual On/Off, 0:05, 0:10, 0:015...) Move to previous/next menu item This menu will appear only if the Lights are configured for countdown timer. This setting is the time after you manually turn on the lights until the Pro Logic automatically turns off the lights. You can also manually turn off the lights at an earlier time by pressing the LIGHTS button. If the Lights relay is on during the programmed off time, it may be because of freeze protection. Aux1 and Aux2 configurations are identical. Set DAauyx1a-nadllTime W8e:d3n0eAsdtaoy 41:00:03P7P or Aux1-wkend 8:30A to 4:00P Adjust time setting Move between start and stop times & to previous/next menu item Adjust time setting Move between start and stop times & to previous/next menu item Aux1-wkday 8:30A to 4:00P Adjust time setting Move between start and stop times & to previous/next menu item or This menu will appear only if the Aux1 is configured for timeclock. The Aux output will turn on and off at the designated times. If the Aux relay is off during the programmed on time- note that some pool equipment (example pressure side pool cleaner) can only be operated when the filter pump is running and the pool/spa valves are in the pool-only position-the Pro Logic will keep the relay off until these other conditions are suitable for operation. If the Aux relay is on during the programmed off time, it may be because of freeze protection. Also, manual operation overrides the timeclock. Aux1-CountDn 0:20 Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15...) Move to previous/next menu item This menu will appear only if the Aux1 is configured for countdown timer. This setting is the time after you manually turn on the Aux relay until the Pro Logic automatically turns off the relay. You can also manually turn off the relay at an earlier time by pressing the AUX1 button. 12