HealthRider 225p Instruction Manual - Page 8
How To Fold And Move The Treadmill
View all HealthRider 225p manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
7. Place the Console Base (46) on the Handrails (1) (only the Right Handrail is shown). Pull out just enough of the two Wires (21) to connect them to the receptacles in the Console Base. Make a loop with the indicated plastic tie and insert the two Wires through the loop. Locate the Wire that has a two-pin connector and a three-pin connector on the end. Plug the connectors into the matching receptacles in the Console Base. If the connectors do not fit easily, rotate them and then plug them in. Slide the Wire Cover (66) onto the connectors so that they are completely covered. Next, plug the other Wire into the matching receptacle on the Console Base. WARNING: Do not connect or disconnect the Wires whilst the treadmill power cord is plugged in. Tighten the plastic tie and cut off the end. 7 1 Tie 66 See the inset drawing. Loop one of the included plastic ties around the Wire Cover (66) so that the plastic tie is in the two notches in the Wire Cover. Tighten the plastic tie and cut off the end. 8 8. Thread four Long Screws (3) into the Handrails (1) and the Console Base (46). Make sure that the wires in the Right Handrail are clear of the screw holes. After all four Long Screws have been started, tighten them until they are snug; do not overtighten them. 46 21 66 Tie 46 The console requires three 1.5 V batteries. Alkaline batteries are recommended. To install batteries, first touch the Uprights (11) to discharge any static. Next, open the Battery Cover (4) as shown. Insert three batteries into the battery compartment, making sure that the negative (-) ends of the batteries are touching the springs in the battery compartment. Close the Battery Cover, push up on the tab, and then push the tab forward as shown in the inset drawing. Make sure that the tab locks into place. Remove the plastic ties used in step 6. 4 Batteries 3 3 1 4 Tab 9. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 16). To protect the floor or carpet, place a mat under the treadmill. 8 HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, unplug the power cord. CAUTION: You must be able to safely lift 20 kg (45 lbs.) to raise, lower, or move the treadmill. 1. Hold the treadmill with your hands in the locations shown at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Raise the treadmill until the storage latch closes over the catch. It may be helpful to push out on the handrail as you raise the treadmill. Make sure that the storage latch is fully engaged over the catch. To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F). HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the storage latch is fully engaged over the catch. 1. Hold the upper ends of the handrails. Place one foot on the base as shown. 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution whilst moving the treadmill. Do not move the treadmill over an uneven surface. 3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position. Storage Latch Catch Engaged Base Front Wheels 13