HP 3115m HP 3115m Notebook PC - Maintenance and Service Guide - Page 51

Hard drive, Remove the Phillips PM2.5×5.7 screw - hard drive replacement

Get HP 3115m PDF manuals and user guides View all HP 3115m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Hard drive NOTE: The hard drive spare part kit does not include the hard drive bracket, connector cable, isolators, or screws. These components are included in the Hard Drive Hardware Kit, spare part number 664913-001. Description 500-GB, 5400-rpm, SATA, 7.0-mm 320-GB, 5400-rpm, SATA, 7.0-mm Spare part number 669299-001 645193-001 Before removing the hard drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 32). 5. Remove the service cover (see WLAN module on page 37). Remove the hard drive: 1. Disconnect the hard drive connector cable (1) from the system board. 2. Remove the Phillips PM2.5×5.7 screw (2) that secures the hard drive to the computer. 3. Use the tab (3) on the hard drive bracket to lift the left side of the hard drive until it rests at an angle. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Hard drive
NOTE:
The hard drive spare part kit does not include the hard drive bracket, connector cable,
isolators, or screws. These components are included in the Hard Drive Hardware Kit, spare part
number 664913-001.
Description
Spare part number
500-GB, 5400-rpm, SATA, 7.0-mm
669299-001
320-GB, 5400-rpm, SATA, 7.0-mm
645193-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the battery (see
Battery
on page
32
).
5.
Remove the service cover (see
WLAN module
on page
37
).
Remove the hard drive:
1.
Disconnect the hard drive connector cable
(1)
from the system board.
2.
Remove the Phillips PM2.5×5.7 screw
(2)
that secures the hard drive to the computer.
3.
Use the tab
(3)
on the hard drive bracket to lift the left side of the hard drive until it rests at
an angle.
Component replacement procedures
43