HP 6125XLG HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines
HP 6125XLG Manual
 |
View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 6125XLG manual content summary:
- HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 1
HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines Part Number: 5998-5007 Published: October 2013 Edition: 1.0 - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 3
Contents Introduction ...4 Configuration of NPV mode ...5 Configuration Procedure ...5 FCoE Configuration...5 PFC Configuration...5 ETS Configuration ...5 DCBX Configuration ...5 Configuration Example ...6 Contents 3 - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 4
This paper outlines the configuration steps necessary to use the HP 6125XLG blade switch as an NPV (N_Port Virtualization) FCoE Switch. The HP 6125XLG can be used as an NPV Switch to connect servers attached to its downlink ports to the FC/FCoE SAN fabric. An NPV switch allows the size of - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 5
of the 6125XLG as an NPV Switch. Each of these configuration steps is described below. FCoE Configuration The following should be configured: FCoE mode FCoE VSAN and VLAN VFC (Virtual FC) interfaces for downlinks and uplinks PFC Configuration The following should be configured for each port - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 6
downlinks (1/0/1 and 1/0/2) to two CNA's and # a single Ethernet LACP link-aggregated uplink (1/1/5 and 1/1/6) to the FCoE FCF switch # # Default VLAN 1 carries untagged Ethernet data traffic # VLAN 200 carries tagged FCoE traffic # # This configuration can be done in system-view, or it can be added - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 7
interface vfc1 bind interface Ten-GigabitEthernet 1/0/1 port trunk vsan 10 interface vfc2 bind interface Ten-GigabitEthernet 1/0/2 port trunk vsan 10 # Create VFC (Virtual FC) interface on uplink aggregate interface as NP_Port to FCF switch interface vfc100 bind interface Bridge-Aggregation1 fc - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 8
5 export 0 import 6 export 0 import 7 export 0 # Configure WRR bandwidth on all FCoE downlinks and uplinks # Guarantee 50% for FCoE and 50% for Ethernet data traffic # Trust incoming 802.1p priority on all FCoE downlinks and uplinks interface range Ten-GigabitEthernet 1/0/1 Ten-GigabitEthernet - HP 6125XLG | HP 6125XLG Blade Switch FCoE NPV Mode Configuration Guidelines - Page 9
# DCBX Configuration # Enable LLDP lldp global enable # Define ACL for FCoE and FIP packets acl number 4000 rule permit type 8906 ffff rule permit type 8914 ffff # Define FCoE class traffic classifier fcoe-class operator or if-match acl 4000 # Define FCoE behavior traffic behavior fcoe-behav remark
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
HP 6125XLG Blade Switch
FCoE NPV Mode Configuration Guidelines
Part Number: 5998-5007
Published: October 2013
Edition: 1.0