HP BL2x220c HP ProLiant BL2x220c Generation 5 Server Blade User Guide - Page 24

Installing DIMMs, Mezzanine card option

Get HP BL2x220c - ProLiant - G5 Server A PDF manuals and user guides View all HP BL2x220c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

• Install only ECC PC2-5300 Registered DDR2 SDRAM DIMMs that meet the following specifications: o Supply voltage: 1.8 V o Bus width: 72 bits • Always install DIMMs in sequence (1A, 2B, 3C, 4D). Each server supports up to 16 GB of memory when 4-GB memory modules are installed. The amount of memory supported is independent of the processor configuration. Each server supports multiple memory modes, based on DIMM population. The system will default to Advanced ECC. To select a mode, use RBSU ("HP ROM-Based Setup Utility" on page 45). Installing DIMMs To install the component: 1. Power down the server blade (on page 13). 2. Remove the server blade (on page 14). 3. Access the internal server components (on page 14). 4. Open the DIMM slot latches. IMPORTANT: Always install memory in pairs of two identical DIMMs. 5. Install the DIMM. 6. Install the server B assembly ("Install server B assembly" on page 15). 7. Install the server blade ("Installing a server blade" on page 19). Mezzanine card option Optional mezzanine cards are classified as Type I mezzanine cards and Type II mezzanine cards. The server blade supports only Type I mezzanine cards. Hardware options installation 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Hardware options installation 24
•
Install only ECC PC2-5300 Registered DDR2 SDRAM DIMMs that meet the following specifications:
o
Supply voltage: 1.8 V
o
Bus width: 72 bits
•
Always install DIMMs in sequence (1A, 2B, 3C, 4D).
Each server supports up to 16 GB of memory when 4-GB memory modules are installed. The amount of
memory supported is independent of the processor configuration.
Each server supports multiple memory modes, based on DIMM population. The system will default to
Advanced ECC. To select a mode, use RBSU ("
HP ROM-Based Setup Utility
" on page
45
).
Installing DIMMs
To install the component:
1.
Power down the server blade (on page
13
).
2.
Remove the server blade (on page
14
).
3.
Access the internal server components (on page
14
).
4.
Open the DIMM slot latches.
IMPORTANT:
Always install memory in pairs of two identical DIMMs.
5.
Install the DIMM.
6.
Install the server B assembly ("
Install server B assembly
" on page
15
).
7.
Install the server blade ("
Installing a server blade
" on page
19
).
Mezzanine card option
Optional mezzanine cards are classified as Type I mezzanine cards and Type II mezzanine cards. The
server blade supports only Type I mezzanine cards.