HP Cisco MDS 8/12c Release Notes HP C-series Fabric Switches for NX-OS 5.2(2) - Page 23

Hp Sn6000c Fabric Switch, Cisco Mds 8gb Fabric Switch For Hp, Bladesystem C-class

Page 23 highlights

5. Enter the following command to enable the VSAN(s) that contain the Continuous Access EVA and/or DRM fabric to src-dst-id loadbalancing: switch(config-vsan-db)# vsan loadbalancing src-dst-id switch(config-vsan-db)# exit switch(config)# exit 6. Verify that src-dst-id is enabled for the desired VSAN by entering the following command: switch# show vsan In the following example, VSAN 1 loadbalancing is set to src-id/dst-id switch# show vsan 1 vsan 1 information name: vsan1 state: active interoperability mode: default loadbalancing: src-id/dst-id operational state: up 7. Type the following to copy the running configuration into the startup configuration: switch# copy running-config startup-config Refer to the Fabric Configuration Guide, Cisco DCNM for SAN, Cisco DCNM for SAN, Release 5.x to set LoadBalancing value to srcdst using Device Manager/DCNM. Note: The running configuration overwrites the startup configuration. HP SN6000C FABRIC SWITCH The HP SN6000C Fabric Switches (MDS 9148) have fixed configurations with 16 and 32 full rate 8-Gbps fibre channel ports. The switch can be upgraded up to 48-ports in 8 port increments with an on demand port activation license. CISCO MDS 8Gb FABRIC SWITCH FOR HP BLADESYSTEM c-CLASS The Cisco MDS 8Gb 12-port fabric switch and the MDS Cisco 8Gb 24-port fabric switch for HP BladeSystem c-Class have fixed configurations with 8-internal/4-external or 16-internal/8external full rate 8-Gbps fibre channel ports. The 12-port switch can be upgraded to the 24-port switch with an on demand port activation license. Note: For the latest supported mezzanine software, refer to the HP Single Point of Connectivity Knowledge (SPOCK) website at http://www.hp.com/storage/spock. You must sign up for an HP Passport to be granted access. For the latest supported c-Class Onboard Administrator firmware, refer to hp.com. Note: It is recommended to set the mezzanine adapter to the desired port speed instead of using the default speed of auto. 23 MDS 9000 Series Multilayer Director & Multilayer Fabric Switches Release Notes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30

23
MDS 9000 Series Multilayer Director & Multilayer Fabric Switches Release Notes
5.
Enter the following command to enable the VSAN(s) that contain the Continuous Access
EVA and/or DRM fabric to src-dst-id loadbalancing:
switch(config-vsan-db)# vsan
<1-4094>
loadbalancing src-dst-id
switch(config-vsan-db)# exit
switch(config)# exit
6.
Verify that src-dst-id is enabled for the desired VSAN by entering the following
command:
switch# show vsan
<1-4094>
In the following example, VSAN 1 loadbalancing is set to src-id/dst-id
switch# show vsan 1
vsan 1 information
name: vsan1
state: active
interoperability mode: default
loadbalancing: src-id/dst-id
operational state: up
7.
Type the following to copy the running configuration into the startup configuration:
switch# copy running-config startup-config
Refer to the
Fabric Configuration Guide, Cisco DCNM for SAN, Cisco DCNM for SAN, Release
5.x
to set
LoadBalancing
value to srcdst
using Device Manager/DCNM.
Note:
The running configuration overwrites the startup configuration.
HP SN6000C FABRIC SWITCH
The HP SN6000C Fabric Switches (MDS 9148) have fixed configurations with 16 and 32 full
rate 8-Gbps fibre channel ports.
The switch can be upgraded up to 48-ports in 8 port increments
with an on demand port activation license.
CISCO MDS 8Gb FABRIC SWITCH FOR HP
BLADESYSTEM c-CLASS
The Cisco MDS 8Gb 12-port fabric switch and the MDS Cisco 8Gb 24-port fabric switch for HP
BladeSystem c-Class have fixed configurations with 8-internal/4-external or 16-internal/8-
external full rate 8-Gbps fibre channel ports.
The 12-port switch can be upgraded to the 24-port
switch with an on demand port activation license.
Note
:
For the latest supported mezzanine software, refer to the HP Single Point of Connectivity
Knowledge (SPOCK) website at
.
You must sign up for an HP Passport
to be granted access.
For the latest supported c-Class Onboard Administrator firmware, refer to hp.com.
Note
:
It is recommended to set the mezzanine adapter to the desired port speed instead of using the default
speed of auto.