HP Cisco MDS 8/24c Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Rel - Page 37

Open Caveats

Get HP Cisco MDS 8/24c PDF manuals and user guides View all HP Cisco MDS 8/24c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Caveats Send documentation comments to [email protected] !--ip access-list 150 deny udp any any eq port snmp ip access-list 150 deny tcp any any eq port snmp !--!--- Permit/deny all other Layer 3 and Layer 4 traffic in !--- accordance with existing security policies and !--- configurations. Permit all other traffic to transit the !--- device. !--access-list 150 permit ip any any !--- Apply access-list to management interface interface serial 2/0 ip access-group 150 in For more information on IP Access Control Lists see the "Configuring IPv4 and IPv6 Access Control List" section in the Cisco MDS 9000 Family NX-OS Security Configuration Guide at the following location: http://www.cisco.com/en/US/docs/switches/datacenter/mds9000/sw/5_0/configuration/guides/sec/ nxos/ipacl.html For more information on IP Access Control Lists see the "Configuring ACLs" section in the Cisco Nexus 5000 Series NX-OS Software Configuration Guide at the following location: http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/configuration/guide/cli_rel_ 4_0_1a/sec_ipacls.html Workaround: This issue is resolved. • CSCto62199 Symptom: The MDS 9222i switch spontaneously reboots itself. The output of the show system exception command includes the following stack trace output: STACK Call Trace: []str_isr_handle_cpm_one_intr_reg+0x94/0x310 [klm_str] []str_isr_cpm_0to3+0xf8/0x154 [klm_str] []str_isr_bh+0x1bc/0x218 [klm_str] []worker_thread+0x17c/0x228 []kthread+0xec/0x128 []original_kernel_thread+0x44/0x60 Workaround: This issue is resolved. Open Caveats • CSCtn72391 Symptom: Following a switch reload or a software upgrade, the startup configuration occasionally does not display feature fcip. Workaround: Once the switch is completely up, copy the running configuration to the startup configuration by entering the copy running-config startup-config command. • CSCtn68418 Symptom: When you try to save a configuration, you might see the following message: switch# copy run start 100% OL-21012-06 Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.0(4d) 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Send documentation comments to [email protected]
37
Cisco MDS 9000 Family Release Notes for Cisco MDS NX-OS Release 5.0(4d)
OL-21012-06
Caveats
!---
ip access-list 150 deny udp any any eq port snmp
ip access-list 150 deny tcp any any eq port snmp
!---
!--- Permit/deny all other Layer 3 and Layer 4 traffic in
!--- accordance with existing security policies and
!--- configurations.
Permit all other traffic to transit the
!--- device.
!---
access-list 150 permit ip any any
!--- Apply access-list to management interface
interface serial 2/0
ip access-group 150 in
For more information on IP Access Control Lists see the “Configuring IPv4 and IPv6 Access
Control List” section in the
Cisco MDS 9000 Family NX-OS Security Configuration Guide
at the
following location:
nxos/ipacl.html
For more information on IP Access Control Lists see the “Configuring ACLs” section in the
Cisco
Nexus 5000 Series NX-OS Software Configuration Guide
at the following location:
4_0_1a/sec_ipacls.html
Workaround
: This issue is resolved.
•
CSCto62199
Symptom
: The MDS 9222i switch spontaneously reboots itself. The output of the
show system
exception
command includes the following stack trace output:
STACK
Call Trace:
[<f724ebf4>]str_isr_handle_cpm_one_intr_reg+0x94/0x310 [klm_str]
[<f724f4dc>]str_isr_cpm_0to3+0xf8/0x154 [klm_str]
[<f72510c0>]str_isr_bh+0x1bc/0x218 [klm_str]
[<c004cf50>]worker_thread+0x17c/0x228
[<c0052a8c>]kthread+0xec/0x128
[<c001bdf0>]original_kernel_thread+0x44/0x60
Workaround
: This issue is resolved.
Open Caveats
•
CSCtn72391
Symptom
: Following a switch reload or a software upgrade, the startup configuration occasionally
does not display feature fcip.
Workaround
: Once the switch is completely up, copy the running configuration to the startup
configuration by entering the
copy running-config startup-config
command.
•
CSCtn68418
Symptom
: When you try to save a configuration, you might see the following message:
switch#
copy run start
[########################################] 100%