HP ENVY 15-bq000 Maintenance and Service Guide - Page 59

Display assembly, Release the WLAN antenna cables

Get HP ENVY 15-bq000 PDF manuals and user guides View all HP ENVY 15-bq000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Display assembly NOTE: The display assembly is spared at the subcomponent level. For display assembly spare part information, see the individual removal subsections. Before removing the display assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet, and then unplugging the AC adapter from the computer. 4. Remove the bottom cover (see Bottom cover on page 29), and then remove the following components: a. Battery (see Battery on page 31) b. System board (see System board on page 42) c. Speakers (see Speakers on page 49) Remove the display assembly: 1. Remove the six Phillips PM2.5×4.3 screws that secure the display assembly to the keyboard/top cover. 2. Release the WLAN antenna cables (1) and the webcam/microphone module cable from the retention clip built into the keyboard/top cover. 3. Release the display panel cable (2) from the retention clip built into the keyboard/top cover. 4. Swing the display hinges (3) up and back. 5. Swing the keyboard/top cover (4) up and back until it separates from the display assembly. Component replacement procedures 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Display assembly
NOTE:
The display assembly is spared at the subcomponent level. For display assembly spare part
information, see the individual removal subsections.
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is
off
or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by
first
unplugging the power cord from the AC outlet, and
then unplugging the AC adapter from the computer.
4.
Remove the bottom cover (see
Bottom cover
on page
29
), and then remove the following components:
a.
Battery (see
Battery
on page
31
)
b.
System board (see
System board
on page
42
)
c.
Speakers (see
Speakers
on page
49
)
Remove the display assembly:
1.
Remove the six Phillips PM2.5×4.3 screws that secure the display assembly to the keyboard/top cover.
2.
Release the WLAN antenna cables
(1)
and the webcam/microphone module cable from the retention clip
built into the keyboard/top cover.
3.
Release the display panel cable
(2)
from the retention clip built into the keyboard/top cover.
4.
Swing the display hinges
(3)
up and back.
5.
Swing the keyboard/top cover
(4)
up and back until it separates from the display assembly.
Component replacement procedures
51