HP ENVY Spectre XT Ultrabook 13-2000 SpectreXT Maintenance and Service Guide - Page 50

Remove the system board see

Get HP ENVY Spectre XT Ultrabook 13-2000 PDF manuals and user guides View all HP ENVY Spectre XT Ultrabook 13-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

3. Remove the Phillips PM screws securing each half of the front speaker (2). 4. Remove the speaker cables (3) that are routed on each side of the front area. 5. Remove the speakers (4). Reverse this procedure to install the front speakers. Before removing the rear speaker, follow these steps; 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the base enclosure (see Base enclosure on page 27). 5. Disconnect the battery cable (see Battery on page 29). 6. Remove the system board (see System board on page 37). NOTE: The heat sink overlaps the rear speakers so the system board must be removed before the rear speakers. Remove the rear speakers 1. Disconnect the rear speaker cable from the USB/Audio board (1). 42 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
3.
Remove the Phillips PM screws securing each half of the front speaker
(2)
.
4.
Remove the speaker cables
(3)
that are routed on each side of the front area.
5.
Remove the speakers
(4)
.
Reverse this procedure to install the front speakers.
Before removing the rear speaker, follow these steps;
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the base enclosure (see
Base enclosure
on page
27
).
5.
Disconnect the battery cable (see
Battery
on page
29
).
6.
Remove the system board (see
System board
on page
37
).
NOTE:
The heat sink overlaps the rear speakers so the system board must be removed before
the rear speakers.
Remove the rear speakers
1.
Disconnect the rear speaker cable from the USB/Audio board
(1)
.
42
Chapter 4
Removal and replacement procedures