HP ENVY x2 HP Envy x2 Maintenance and Service Guide IMPORTANT! This document i - Page 42

Hinge assembly removal, Remove the two 5.0-mm screws

Get HP ENVY x2 PDF manuals and user guides View all HP ENVY x2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Hinge assembly removal Description Hinge assembly Spare part number 702354-001 Before removing the hinge, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the base enclosure (see Base enclosure on page 28). 5. Disconnect the battery cable (see Battery on page 29). Remove the hinge assembly: 1. Disconnect the hinge assembly left cable (1), and then disconnect the hinge assembly right cable (2). NOTE: The right hinge assembly cable may will already be disconnected if the multimedia board has been removed. 2. Remove the two 5.0-mm screws (3) on the outside screw hole, and then remove the 2 3.0-mm screws (4) on the inside screw hole. 3. Remove the hinge assembly (5). When removing the hinge assembly, make sure you account for the hinge assembly right cable (6). Reverse this procedure to install the hinge assembly. 34 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Hinge assembly removal
Description
Spare part number
Hinge assembly
702354-001
Before removing the hinge, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the base enclosure (see
Base enclosure
on page
28
).
5.
Disconnect the battery cable (see
Battery
on page
29
).
Remove the hinge assembly:
1.
Disconnect the hinge assembly left cable
(1)
, and then disconnect the hinge assembly right
cable
(2)
.
NOTE:
The right hinge assembly cable may will already be disconnected if the multimedia
board has been removed.
2.
Remove the two 5.0-mm screws
(3)
on the outside screw hole, and then remove the 2 3.0-mm
screws
(4)
on the inside screw hole.
3.
Remove the hinge assembly
(5)
. When removing the hinge assembly, make sure you account
for the hinge assembly right cable
(6)
.
Reverse this procedure to install the hinge assembly.
34
Chapter 4
Removal and replacement procedures