HP EliteBook 830 Maintenance and Service Guide - Page 79

Disconnect the display cable from the ZIF connector, on the hub board.

Get HP EliteBook 830 PDF manuals and user guides View all HP EliteBook 830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

l. Leave the computer upright on the table for 10 minutes to be sure the panel sits correctly in the display. m. Open the display and remove rubber spacer strips. 11. When installing the display hinges, use the following illustration to determine proper cable routing. The WWAN antenna cables and display cable route through the right hinge (1). The WLAN antenna cables and display cable route through the left hinge (2). 12. If you need to remove the hub board from the display: a. Disconnect the display cable from the ZIF connector (1) on the hub board. b. Disconnect the camera cable from the ZIF connector (2) on the hub board. c. Disconnect the smaller cables from the reverse ZIF connectors on the hub board (3). d. Use a tool (4) to release the board from the display rear cover (5). The hub board is available as spare part number M07211-001 in models with an IR camera and M07210-001 in models with an RGB camera or microphone module. Component replacement procedures 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
l.
Leave the computer upright on the table for 10 minutes to be sure the panel sits correctly in the
display.
m.
Open the display and remove rubber spacer strips.
11.
When installing the display hinges, use the following illustration to determine proper cable routing. The
WWAN antenna cables and display cable route through the right hinge
(1)
. The WLAN antenna cables and
display cable route through the left hinge
(2)
.
12.
If you need to remove the hub board from the display:
a.
Disconnect the display cable from the ZIF connector
(1)
on the hub board.
b.
Disconnect the camera cable from the ZIF connector
(2)
on the hub board.
c.
Disconnect the smaller cables from the reverse ZIF connectors on the hub board
(3)
.
d.
Use a tool
(4)
to release the board from the display rear cover
(5)
.
The hub board is available as spare part number M07211-001 in models with an IR camera and
M07210-001 in models with an RGB camera or microphone module.
Component replacement procedures
69