HP G62-166SB Compaq Presario CQ62 Notebook PC and HP G62 Notebook PC - Mainten - Page 53

from the hard drive bay., Remove the hard drive

Get HP G62-166SB PDF manuals and user guides View all HP G62-166SB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Removal and replacement procedures 3. Remove the three Phillips PM2.5×5.0 screws 1 that secure the hard drive to the computer. 4. Grasp the Mylar tabs 2 on the hard drive, and then slide the hard drive to the left to disconnect it from the system board. 5. Disconnect the hard drive cable from the system board 3. 6. Remove the hard drive 4 from the hard drive bay. 7. To replace the hard drive bracket, remove the four Phillips PM3.0×4.0 hard drive bracket screws 1 from each side of the hard drive. 8. Grasp the 2 attached Mylar tabs 2 and pull the bracket straight up to remove it from the hard drive. Reverse this procedure to reassemble and install the hard drive. Maintenance and Service Guide 4-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Removal and replacement procedures
Maintenance and Service Guide
4–9
3. Remove the three Phillips PM2.5×5.0 screws
1
that secure the hard drive to the computer.
4. Grasp the Mylar tabs
2
on the hard drive, and then slide the hard drive to the left to disconnect it from
the system board.
5. Disconnect the hard drive cable from the system board
3
.
6. Remove the hard drive
4
from the hard drive bay.
7. To replace the hard drive bracket, remove the four Phillips PM3.0×4.0 hard drive bracket screws
1
from each
side of the hard drive.
8. Grasp the 2 attached Mylar tabs
2
and pull the bracket straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.