HP HDX X18T-1200 HP HDX 18 Entertainment PC - Maintenance and Service Guide - Page 45

Lift the Mylar sleeve, Remove the left and right hard drive brackets

Get HP HDX X18T-1200 PDF manuals and user guides View all HP HDX X18T-1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

3. Disconnect the hard drive cable 1 from the system board. 4. Grasp the Mylar tabs 2 on the hard drive and slide the hard drive 3 away from the hard drive connector. 5. Remove the hard drive 4 from the hard drive bay. 6. If it is necessary to replace the left and right hard drive brackets, Mylar sleeve, connector, and isolators: a. Remove the two Phillips PM3.0×4.0 hard drive bracket screws 1 from each side of the hard drive. b. Remove the left and right hard drive brackets 2. c. Lift the Mylar sleeve 3 straight up to remove it from the hard drive. d. Remove the hard drive connector 4. e. Remove the four isolators 5. Reverse this procedure to reassemble and install the hard drives. Removal and replacement procedures 4-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Removal and replacement procedures
4–12
3. Disconnect the hard drive cable
1
from the system board.
4. Grasp the Mylar tabs
2
on the hard drive and slide the hard drive
3
away from the hard drive connector.
5. Remove the hard drive
4
from the hard drive bay.
6. If it is necessary to replace the left and right hard drive brackets, Mylar sleeve, connector, and isolators:
a.
Remove the two Phillips PM3.0×4.0 hard drive bracket screws
1
from each side of the hard drive.
b.
Remove the left and right hard drive brackets
2
.
c.
Lift the Mylar sleeve
3
straight up to remove it from the hard drive.
d.
Remove the hard drive connector
4
.
e.
Remove the four isolators
5
.
Reverse this procedure to reassemble and install the hard drives.