HP Integrity rx4640 FC2143 and FC2243 4Gb PCI-X 2.0 Host Bus Adapters for Linu - Page 14

Removing, bracket

Get HP Integrity rx4640 PDF manuals and user guides View all HP Integrity rx4640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Installing the HBA To install the HBA: 1. Turn off the computer. 2. Open and remove the computer cover. 3. Wearing an anti-static wrist strap, remove the blank panel from an empty PCI-X slot. NOTE: The HBA comes with a standard PCI bracket installed. In addition, HP provides a low-profile mounting bracket in the box with the HBA. This low-profile bracket is shorter than the standard bracket: approximately 7.9 cm (3.11 in.) compared to 12.06 cm (4.75 in.) long. 4. If you require a different mounting bracket follow these steps, otherwise, go to step 5. a. Remove the mounting bracket screws from the top of the HBA. Figure 1 Removing the bracket b. Remove the bracket and store it for future use. c. Align the new mounting bracket tabs with the holes in the HBA. NOTE: Be careful not to push the bracket past the transceiver housing's grounding tabs. Ensure that the light emitting diodes (LEDs) are properly aligned with the holes in the bracket. d. Replace the screws that attach the HBA to the bracket. 5. Inset the HBA into the slot and press firmly until the HBA is seated properly. NOTE: Some HP server models support only PCI-X HBAs inserted in optional PCI-X riser cards or cages. For instructions on installing the riser card or cage, see your server documentation. 6. Secure the HBA to the chassis, following the server manufacturer's instructions. 7. Replace and close the computer cover. Insert and tighten the computer cover screws. 14 Installing the HBAs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
Installing
the
HBA
To
install
the
HBA:
1.
Turn
off
the
computer.
2.
Open
and
remove
the
computer
cover.
3.
Wearing
an
anti-static
wrist
strap,
remove
the
blank
panel
from
an
empty
PCI-X
slot.
NOTE:
The
HBA
comes
with
a
standard
PCI
bracket
installed.
In
addition,
HP
provides
a
low-pro
fi
le
mounting
bracket
in
the
box
with
the
HBA.
This
low-pro
fi
le
bracket
is
shorter
than
the
standard
bracket:
approximately
7.9
cm
(3.11
in.)
compared
to
12.06
cm
(4.75
in.)
long.
4.
If
you
require
a
different
mounting
bracket
follow
these
steps,
otherwise,
go
to
step
5
.
a.
Remove
the
mounting
bracket
screws
from
the
top
of
the
HBA.
Figure
1
Removing
the
bracket
b.
Remove
the
bracket
and
store
it
for
future
use.
c.
Align
the
new
mounting
bracket
tabs
with
the
holes
in
the
HBA.
NOTE:
Be
careful
not
to
push
the
bracket
past
the
transceiver
housing’s
grounding
tabs.
Ensure
that
the
light
emitting
diodes
(LEDs)
are
properly
aligned
with
the
holes
in
the
bracket.
d.
Replace
the
screws
that
attach
the
HBA
to
the
bracket.
5.
Inset
the
HBA
into
the
slot
and
press
fi
rmly
until
the
HBA
is
seated
properly.
NOTE:
Some
HP
server
models
support
only
PCI-X
HBAs
inserted
in
optional
PCI-X
riser
cards
or
cages.
For
instructions
on
installing
the
riser
card
or
cage,
see
your
server
documentation.
6.
Secure
the
HBA
to
the
chassis,
following
the
server
manufacturer’s
instructions.
7.
Replace
and
close
the
computer
cover.
Insert
and
tighten
the
computer
cover
screws.
14
Installing
the
HBAs