HP Jetdirect 2700w HP Jetdirect 2700w USB Solution Print Server - Administrato - Page 2

Overview, Telnet Commands and Parameters - usb wireless print server

Get HP Jetdirect 2700w PDF manuals and user guides View all HP Jetdirect 2700w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Overview This addendum describes the changes to the HP Jetdirect Print Servers Administrator's Guide that are required for the HP Jetdirect 2700w USB Solution Print Server. Note: For complete information about HP Jetdirect print servers, see the HP Jetdirect Print Servers Administrator's Guide at: http://h20000.www2.hp.com/bizsupport/TechSupport/Product.jsp?lang=en&cc=us&taskId=101&contentType=S upportManual&docIndexId=64255&prodTypeId=18972&prodCatId=236254 Telnet Commands and Parameters The following table lists the new or modified telnet commands for the HP Jetdirect 2700w Print Server. Command Description Wireless Mode Guard Interval AMSDU Aggregation Block ACKs AMPDU Aggregation SLP Client-Mode LLMNR 802.11 wireless mode. B/G_MODE: Use 802.11b or g. B/G/N_MODE (default): Use 802.11b, g, or n. The space between transmitted symbols (characters). Can eliminate inter-symbol interference (ISI), which occurs when echoes or reflections from one symbol interfere with another. A long interval can reduce echoes, but decrease the data rate. A short interval can increase the data rate by approximately 10 percent. AUTO (default): Set the guard interval based on the wireless mode. SHORT: Set to short interval (400 ns). LONG: Set to a long interval (800 ns). Aggregating 802.11 MAC service data units packs them into frames to reduce overhead and increase the data rate. Enabling aggregation allows a maximum frame size of 7935 bytes. ENABLE (default): Enable aggregation. DISABLE: Disable aggregation. Use block acknowledgement of AMPDUs. This mechanism allows each of the aggregated data frames to be individually acknowledged or retransmitted if affected by an error. (This command is only available when AMPDU Aggregation is enabled.) ENABLE (default): Enable AMPDU block acknowledgements. DISABLE: Disable AMPDU block acknowledgements. Aggregating 802.11 MAC protocol data units packs them into frames to reduce overhead and increase the data rate. Enabling aggregation allows a maximum frame size of 64k bytes. ENABLE (default): Enable aggregation. DISABLE: Disable aggregation. Use the service location protocol (SLP) to locate and install printers on the network. 0 (default): Disable. 1: Enable. Use link local multicast name resolution (LLMNR). 0: Disable. 1 (default): Enable. 2

  • 1
  • 2
  • 3
  • 4
  • 5
2
Overview
This addendum describes the changes to the
HP Jetdirect Print Servers Administrator’s Guide
that are
required for the HP Jetdirect 2700w USB Solution Print Server.
Note:
For complete information about HP Jetdirect print servers, see the
HP Jetdirect Print Servers
Administrator’s Guide
at:
upportManual&docIndexId=64255&prodTypeId=18972&prodCatId=236254
Telnet Commands and Parameters
The following table lists the new or modified telnet commands for the HP Jetdirect 2700w Print Server.
Command
Description
Wireless Mode
802.11 wireless mode.
B/G_MODE: Use 802.11b or g.
B/G/N_MODE (default): Use 802.11b, g, or n.
Guard Interval
The space between transmitted symbols (characters). Can eliminate inter-symbol
interference (ISI), which occurs when echoes or reflections from one symbol interfere
with another. A long interval can reduce echoes, but decrease the data rate. A short
interval can increase the data rate by approximately 10 percent.
AUTO (default): Set the guard interval based on the wireless mode.
SHORT: Set to short interval (400 ns).
LONG: Set to a long interval (800 ns).
AMSDU
Aggregation
Aggregating 802.11 MAC service data units packs them into frames to reduce
overhead and increase the data rate. Enabling aggregation allows a maximum frame
size of 7935 bytes.
ENABLE (default): Enable aggregation.
DISABLE:
Disable aggregation.
Block ACKs
Use block acknowledgement of AMPDUs. This mechanism allows each of the
aggregated data frames to be individually acknowledged or retransmitted if affected
by an error. (This command is only available when AMPDU Aggregation is enabled.)
ENABLE (default): Enable AMPDU block acknowledgements.
DISABLE:
Disable AMPDU block acknowledgements.
AMPDU
Aggregation
Aggregating 802.11 MAC protocol data units packs them into frames to reduce
overhead and increase the data rate. Enabling aggregation allows a maximum frame
size of 64k bytes.
ENABLE (default): Enable aggregation.
DISABLE:
Disable aggregation.
SLP Client-Mode
Use the service location protocol (SLP) to locate and install printers on the network.
0 (default): Disable.
1:
Enable.
LLMNR
Use link local multicast name resolution (LLMNR).
0: Disable.
1 (default):
Enable.