HP Jetdirect 2700w HP Jetdirect 2700w USB Solution Print Server - Setup Guide - Page 14

Con the print server using the HP Embedded Web Server - installation

Get HP Jetdirect 2700w PDF manuals and user guides View all HP Jetdirect 2700w manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Configure the print server using the HP Embedded Web Server You can now configure the HP Jetdirect 2700w Print Server by using the HP Embedded Web Server. This is done by accessing the IP address of the printer/MFP in which the print server is installed. The printer/MFP must be directly connected (wired) to your local network. NOTE: You can also configure the HP Jetdirect 2700w Print Server from the printer/MFP's control panel or by using the HP Install Network Printer Wizard (INPW), which is available for download from: www.hp.com/go/inpw_sw Use the following steps to configure the HP Jetdirect 2700w Print Server: 1. Start a supported Web browser from a computer that is connected to your intranet. 2. Enter the IP address of the printer/MFP as the URL. For example: http://nnn.nnn.nnn.nnn/ NOTE: You can typically locate the IP address by using the printer/MFP control panel or by printing a configuration page. The HP Embedded Web Server is displayed. 3. Select the Networking tab. 4. From the Configuration menu, select Wireless. The Wireless page displays all the wireless configuration parameters required to make a wireless connection to your network. 5. To use a wizard, which will guide you through the required 802.11 wireless configuration parameters, click Wireless Wizard in the General section. Remember to click Apply to save your settings. 6. Otherwise, enter the information needed to make a wireless connection to your network. 7. Click Apply to set, or Cancel to ignore your entries. To resent to factory-default values, click Restore Defaults. 6 Chapter 2 Installation ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Configure the print server using the HP Embedded
Web Server
You can now configure the HP Jetdirect 2700w Print Server by using the HP Embedded Web Server.
This is done by accessing the IP address of the printer/MFP in which the print server is installed. The
printer/MFP must be directly connected (wired) to your local network.
NOTE:
You can also configure the HP Jetdirect 2700w Print Server from the printer/MFP's control
panel or by using the HP Install Network Printer Wizard (INPW), which is available for download from:
www.hp.com/
go/inpw_sw
Use the following steps to configure the HP Jetdirect 2700w Print Server:
1.
Start a supported Web browser from a computer that is connected to your intranet.
2.
Enter the IP address of the printer/MFP as the URL. For example: http://nnn.nnn.nnn.nnn/
NOTE:
You can typically locate the IP address by using the printer/MFP control panel or by
printing a configuration page.
The HP Embedded Web Server is displayed.
3.
Select the
Networking
tab.
4.
From the
Configuration
menu, select
Wireless
.
The
Wireless
page displays all the wireless configuration parameters required to make a wireless
connection to your network.
5.
To use a wizard, which will guide you through the required 802.11 wireless configuration
parameters, click
Wireless Wizard
in the
General
section. Remember to click
Apply
to save
your settings.
6.
Otherwise, enter the information needed to make a wireless connection to your network.
7.
Click
Apply
to set, or
Cancel
to ignore your entries. To resent to factory-default values, click
Restore Defaults
.
6
Chapter 2
Installation
ENWW