HP LH4r hp lp 1000r netraid-2m config guide — for Microsoft Windo
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 1
Advanced Server Cluster Configuration Guide Introduction This document defines the server cluster configurations supported by Hewlett-Packard for interconnection of two HP Netserver LP 1000r servers and one or two HP Rack Storage/12 disk drive enclosure(s), with Microsoft® Cluster Server software - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 2
software Navigator CD-ROM Operating system Service pack Power distribution Layout Specification PCI slot 1 IDE CD-ROM, FDD, embedded SCSI, PCI slot 1 Embedded SCSI Sym_u3.sys, version 5.07.00, or later (driver obtained from Navigator CD-ROM L.20.00, or later) Server internal drive bays, or HP - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 3
Server I/O card slot Network interfaces Boot device Specification PCI slot 1, NetRAID-2M shared storage controller Embedded NICs for both intra-cluster (heartbeat) and client LANs Embedded SCSI Intra-Cluster (Heartbeat) LAN Configuration Parameter Network Connection NIC Quantity Model Driver - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 4
Client LAN Configuration Parameter Network Connection NIC Quantity Model Driver Specification Any LAN One Embedded NIC - LAN B Hptxnt5.sys, version 4.02.27, or later (driver obtained from Navigator CD-ROM L.20.00, or later) LP1000R2K2M 11/7/01 4 - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 5
from 1 to 2 RS/12 storage cabinets per NetRAID-2M. 4. When cabling the network, use LAN A on each node for the heartbeat interconnect, and LAN B for the client network connections. LAN A -heartbeat LAN B -client HP Netserver LP 1000r Cluster using HP Rack Storage/12 Cabling Diagram 11/7/01 5 - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 6
LP1000R2K2M Power Cabling to Separate Power Circuits 11/7/01 6 - HP LH4r | hp lp 1000r netraid-2m config guide — for Microsoft Windo - Page 7
Versions 7 November 2001 13 August 2001 Added support for 1.26 GHz models Initial release LP1000R2K2M © Copyright 2001, Hewlett-Packard Company 11/7/01 7
11/7/01
1
HP Netserver LP 1000r with
NetRAID-2M (HP Rack Storage/12)
Windows
°
2000 Advanced Server
Cluster Configuration Guide
Introduction
This document defines the server cluster configurations supported by Hewlett-Packard for interconnection of
two HP Netserver LP 1000r servers and one or two HP Rack Storage/12 disk drive enclosure(s), with
Microsoft
Cluster Server software.
These configurations provide high server cluster availability and
minimize single points of failure (SPOFs).
A configuration certified and supported by both Hewlett-Packard
and Microsoft
is included, but any cluster configuration that conforms to the guidelines of this document
will be supported by Hewlett-Packard.
Deviations from the supported configurations can result in an
inoperative cluster, an operating cluster with degraded performance, or hidden SPOFs.
Therefore, deviations
are not supported.
For revision/update information on this document, refer to
Versions
on page 7.
Cluster Configuration Elements
This section identifies the hardware components, system software, network interfaces, and power distribution
arrangement required to build an operational server cluster supported by Hewlett-Packard.
The various
server cluster elements are listed below and their associated configuration data is detailed in separate tables
and illustrations that follow.
•
Server configuration
•
Shared storage configuration
•
Microsoft
and HP certified server configuration
•
Intra-cluster (heartbeat) LAN configuration
•
Client LAN configuration
•
SCSI cabling and power distribution configuration
Server Configuration
Parameter
Specification
Server
Type
HP Netserver LP 1000r
Number of nodes
Two
Each node must be the same server type, but may have different clock speeds, and
main memory and cache sizes.
Clock speed
1.26 GHz
This certification covers any CPU speed within 500 MHz of the certified rate.
Number of CPUs
Two
BIOS
For CPU clock speeds up to 1 GHz, version range 4.06.12 RA to 4.06.19 RA
For CPU clock speeds of 1.26 GHz, version 4.06.03 RO or later
CPU cache
Any size
RAM
256 MB, minimum.
Must be HP.
Number of power
supplies
One