HP LH4r HP Netserver LH 3r Third Party Rack Installation Guide
HP LH4r - NetServer - 256 MB RAM Manual
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH4r manual content summary:
- HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 1
HP NetServer LH 3r Installation Guide for Compaq® 4000/7000 Racks HP Part Number 5967-5208 Printed in July 1998 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 2
Packard shall not be liable for errors contained herein or for incidental or use or reliability of its software on equipment that is not furnished guide is for the person who installs, administers, and troubleshoots network servers. Hewlett-Packard Company assumes you are qualified in the servicing - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 3
LH 3r - Compaq Rack Precautions 4 2 Overview ...5 3 Installation 7 Preparation...7 Marking the Installation Holes 7 Installing the Bar Nuts, Screws, and Rack Nuts 9 Mounting the Slides 10 Installing the NetServer 11 Installing the Recessed Mounting Brackets 14 4 Warranty and Support 17 HP - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 4
- HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 5
-series rack enclosure. Refer to the HP NetServer LH 3r Road Map and the HP NetServer LH 3/3r User Guide that came with the NetServer for instructions on adding accessories to and configuring the NetServer. The HP NetServer LH 3 (the pedestal version of this NetServer) cannot be installed in a rack - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 6
front of the rack enclosure. Be sure that the stabilizing, anti-tip feature is installed on the rack enclosure in which you are installing the HP NetServer LH 3r. This option consists of two "feet" at the front of the base of the enclosure and, if you are installing this - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 7
Chapter 1 Introduction Figure 1-2. Single Rack Enclosure With the Anti-Tip Stabilizing Feature Installed 3 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 8
installed according to these instructions, damage to the NetServer or accessories may result. Damage due to improper installation is not covered by the HP Warranty. Observe the precautions listed in this section to maintain the NetServer's reliability. When the HP NetServer LH 3r is installed in - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 9
supply modules and hot-swap drives from the NetServer • Lift the NetServer onto the slides • Secure the NetServer to the slides • Remove the lifting handles from the NetServer • Install the power supply modules and hot-swap drives in the NetServer • Push the NetServer back into the chassis • Install - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 10
. Extendible side bracket which is attached to the rack chassis columns on which the NetServer is mounted. Consists of stationary component, and an extendible member (see Figure 3-3). Allows access to the NetServer after it is installed in the rack chassis. Mounting flange located at either end - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 11
section contains detailed instructions for installing an HP NetServer LH 3r in certain models of Compaq rack enclosures. Preparation Before beginning the installation of the NetServer into the rack, you must prepare the rack and the NetServer. Determine the location at which the NetServer is to be - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 12
to use for the rack nuts where the two recessed mounting brackets attach to the columns. When the installation is complete, these brackets secure the NetServer in the rack enclosure. To mark the bracket mounting holes (refer to Figure 3-1): 1. On the left front column, count up from the top of the - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 13
Chapter 3 Installation Installing the Bar Nuts, Screws, and Rack Nuts Once you have marked the appropriate holes, install the bar nuts and screws on the columns: 1. Position one bar nut behind holes 20 and 22 (previously marked). 2. Insert the two screws, with flat washers, through the two holes - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 14
tightening the screws. Tightening the screws without lifting up on the slides will result in interference between the NetServer and other equipment in the rack; you may not be able to slide the NetServer into the rack enclosure after completing the installation. 4. Repeat for the other slide. 10 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 15
, anti-tip feature is installed on this rack enclosure (see Figure 1-2). 2. Before you lift the NetServer, remove the power supply modules and the hot-swap hard disk drives to reduce the weight. WARNING This NetServer weighs up to 160 pounds (73 kg.) when fully configured. Remove all power supply - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 16
the handles are resting on the slide members (see Figure 3-5 and Figure 3-6). Figure 3-5. Lifting the Server Onto the Slide Members 4. Line up the mounting holes in the slide members with the holes in the NetServer chassis, insert the three screws on each side, and tighten them (see Figure 3-6). 12 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 17
Chapter 3 Installation Figure 3-6. Attaching the Slides to the Server Chassis 13 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 18
and screws for later use, in case you need to remove the NetServer and ship it. Figure 3-7. Remove Mounting Handles 6. Reinstall power supply modules and hard disk modules removed earlier. Installing the Recessed Mounting Brackets The NetServer is held in place (inside the rack enclosure) by two - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 19
Chapter 3 Installation To install these brackets: 1. On both slide members, simultaneously depress the lockout releases and push the NetServer completely into the rack enclosure (see Figure 3-8). Lockout Release Figure 3-8. Location of Lockout Releases 15 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 20
chassis (see Figure 3-9). 3. Install the two screws that hold the short, right-hand bracket to the face of the NetServer chassis (see Figure 3-9). Recessed Brackets Figure 3-9. Installing the Recessed Mounting Brackets 4. Install two screws into the two holes in the left-hand recessed bracket - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 21
4 Warranty and Support Refer to the warranty statement provided with your original HP NetServer system documentation for the warranty limitations, customer responsibilities, and other terms and conditions. CAUTION Improper installation of HP rack-mount components into third-party racks may result - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 22
Chapter 4 Warranty and Support HP Repair and Telephone Support Refer to the Service and Support chapter of your HP NetServer system documentation for instructions on how to obtain HP repair and telephone support. 18 - HP LH4r | HP Netserver LH 3r Third Party Rack Installation Guide - Page 23
Index C Compaq, 1 F fastening server to rack front, 14 fastening server to slides, 12 H handles removing after mounting, 14 L lifting server into rack, 12 lockout releases, 15 R recessed brackets, attaching, 16 S slide location, 7 V version of NetServer, 1 19
HP NetServer LH 3r
Installation Guide
for
Compaq
®
4000/7000 Racks
HP Part Number 5967-5208
Printed in July 1998