HP LaserJet MFP M72625-M72630 Engine Install Guide
HP LaserJet MFP M72625-M72630 Manual
 |
View all HP LaserJet MFP M72625-M72630 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LaserJet MFP M72625-M72630 manual content summary:
- HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 1
HP LaserJet MFP M72625, M72630 ( ( Engine Install Guide NJ OE support.hp.com www.hp.com/videos/A3install HP recommends reviewing the video before performing the installation. WARNING: Make sure the work area is free of debris and the floor is not slippery or - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 2
tape and protective packing materials. 4 Remove all packing material and tape from all locations on the engine. NJ OE 4.1 Locate the shipping label instruction tab on the right door. 4.2 Open the right door and then remove the shipping label directing you to the transfer area - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 3
4.4 Remove the foam packaging material. 4.5 Carefully remove the strapping tape at the rear of the transfer unit. 4.6 Open Tray 1 on the right side of the printer, and then remove the foam near the pickup roller. 4.7 Open Tray 2-3 and remove all tape and foam packaging material. 5 Install the - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 4
open the imaging unit package until it is ready to install. Prolonged exposure to bright light can damage the imaging drum and cause image quality problems. 6.1 Ensure that the front and right doors are open. The right door retracts the interlock lever allowing the imaging unit to be installed - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 5
right door is closed. 7.1 9 Load paper in Tray 2. NOTE: Paper is used to print configuration sheets as needed (Letter or A4). 8.1 Install the paper settling guides at two locations on the first exit. 9.1 Open Tray 2. 9.2 Push down on the blue tab in the back of the tray. At the same time - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 6
10 Initialize the printer. CAUTION: Do not connect the network cable at this time. 10.1 Connect the power cord to the printer and the wall receptacle (callout 1). IMPORTANT: Use the printer power switch to turn the printer power on (callout 2). 10.2 10.4 Print a configuration page to make - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 7
7 - HP LaserJet MFP M72625-M72630 | Engine Install Guide - Page 8
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
www.hp.com/videos/A3install
±²³´µ NJ
´¶·³¸ OE
1
support.hp.com
HP LaserJet MFP M72625, M72630
1.1
1.2
1
Engine Install Guide
WARNING
:
Make sure the work area is free of debris and
the floor is not slippery or wet.
CAUTION
:
The printer assembly is heavy. Four people
must lift and install it on the dual cassette feeder (DCF)
(Y1F97A), the 2000-sheet high capacity input (HCI)
(Y1F99A), or the stand (Y1G17A).
Unpack and acclimate the printer.
CAUTION
:
Before the printer is powered on, make sure that the room and equipment are at least 15°C (59°F).
NOTE
:
Leave the printer on the shipping pallet until it is ready to install on a
DCF, HCI, or stand.
Remove the printer, imaging drum, toner collection unit (TCU), and associated hardware from the
box. After unpacking the printer and supplies, allow them to acclimate for four hours.
NOTE
:
If the printer and hardware were stored below 0°C (32°F), it may take them longer
to acclimate.
CAUTION
:
Do not remove the shipping tape or protective packing materials until after the printer
is installed on a DCF, HCI, or stand. (Step 3.2)
NOTE
:
The imaging drum is stored in the output bin area below the automatic document feeder.
Pull the protective clear plastic down to the base of the printer to
allow access to lifting points.
HP recommends reviewing
the video before performing
the installation.
(±²³´´
(±²³´´