HP LaserJet MFP M72625-M72630 Engine Install Guide - Page 2

Prepare the DCF, 2000 sheet HCI, or stand for installation

Get HP LaserJet MFP M72625-M72630 PDF manuals and user guides View all HP LaserJet MFP M72625-M72630 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

2 Prepare the DCF, 2000 sheet HCI, or stand for installation. CAUTION: Use care when lifting. Use proper safe lifting practices. IMPORTANT: Retain two thumbscrews for securing the HCI or stand. 2.1 Follow the in-box directions to unpack the DCF, HCI, or stand. 2.2 Position the DCF, HCI, or stand near the printer. WARNING: Make sure the work area is free of debris and the floor is not slippery or wet. NOTE: If desired, lower the stabilizers to prevent the printer from moving. 3 Install the printer on the DCF, 2000 sheet HCI, or stand. 3.1 Install the two black reusable lifting handles in the hand holds on the left side of the printer (callout 1). Open two lift bars on the right side of the printer (callout 2).  NOTE: Lifting handles are recommended, but are not shipped with the printer (handle set: JC82-00538A). 3.2 Carefully lift the printer assembly and align the printer to the alignment pins and connector on the accessory. Carefully lower the printer onto the accessory. CAUTION: The printer assembly is heavy. Four people must lift and install it on the DCF, the HCI, or the stand. NOTE: On the printer, open each door and all of the trays to check for shipping tape and packing materials. Remove all shipping tape and protective packing materials. 4 Remove all packing material and tape from all locations on the engine.  NJ OE 4.1 Locate the shipping label instruction tab on the right door. 4.2 Open the right door and then remove the shipping label directing you to the transfer area. 2 4.3 Carefully remove the strapping tape at the front of the transfer unit.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
±
±²³´µ NJ
´¶·³¸ OE
±
2
3
2.1
2.2
3.1
3.2
2
4
4.1
4.3
4.2
Follow the in-box directions to unpack the DCF, HCI,
or stand.
Position the DCF, HCI, or stand near
the printer.
WARNING
:
Make sure the work area
is free of debris and the floor is not
slippery or wet.
NOTE
:
If desired, lower the
stabilizers to prevent the printer
from moving.
Install the printer on the DCF, 2000 sheet HCI, or stand.
Install the two black reusable lifting handles in the hand holds on the left
side of the printer (callout 1). Open two lift bars on the right side of the
printer (callout 2).
NOTE
:
Lifting handles are recommended, but are not shipped with the
printer (handle set: JC82-00538A).
Carefully lift the printer assembly and align the printer to the alignment
pins and connector on the accessory. Carefully lower the printer onto
the accessory.
CAUTION
:
The printer assembly is heavy. Four people must lift and
install it on the DCF, the HCI, or the stand.
NOTE
:
On the printer, open each door and all of the trays to check for
shipping tape and packing materials. Remove all shipping tape and
protective packing materials.
Prepare the DCF, 2000 sheet HCI, or stand for installation
.
CAUTION
:
Use care when lifting. Use proper safe lifting practices.
IMPORTANT
:
Retain two thumbscrews for securing the HCI or stand.
Remove all packing material and tape from all locations on the engine.
Locate the shipping label instruction tab on the
right door.
Open the right door and then remove the shipping
label directing you to the transfer area.
Carefully remove the strapping tape at the front of the
transfer unit.