HP Latex 570 Introductory Information - Page 9

Power specifications

Get HP Latex 570 PDF manuals and user guides View all HP Latex 570 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

English Error code 78.2:01 78.3:08 79:03 79:04 79.2:04 19.10:04 19.11:04 19.12:04 81:01 81.1:01 81:03 86:01 86.2:01 87:01 89:11 89.1:10 89.2:10 94:01 94:02 94:08 98:03 Power specifications Recommendation The back tension is lost. This could be due to a loose roll core or an imminent end of roll. If these are not the causes, try unloading and reloading the substrate. Printing with the ink collector is not available in this print mode. Generic firmware error. Update the printer's firmware. It was impossible to stop the servo correctly before setting the encoder position. 1. Turn off the printer. 2. Open the window, observing all safety procedures, and check for any visible obstacles restricting the movement of the drive roller. If there is a wrinkled mass of substrate inside the substrate path, clear the obstruction. 3. Turn on the printer. There is a problem in the carriage assembly. 1. Turn off the printer. 2. Open the window, observing all safety procedures, and check for any visible obstacles restricting the movement of the drive roller. If there is a wrinkled mass of substrate inside the substrate path, clear the obstruction. 3. Turn on the printer. The scan-axis encoder strip is detecting errors in the carriage position. Clean the encoder strip by following the appropriate process in the front panel menu. Some printzone LEDs may be failing or disconnected. The printer will continue operating normally, with only this functionality affected. Color cannot be calibrated on this substrate. White substrate measurement is out of range. Inconsistent colors found. 1. Check that the substrate-type selection in the front panel corrresponds to an actual substrate loaded. 2. Retry calibration. Color calibration failed. Try again. See more details about the color calibration functionality in the user guide. One or more printheads are malfunctioning. Use the printhead status plot to find out which printheads are malfunctioning, and replace them. Specification Input voltage Input frequency Maximum load current (per power cord) Power consumption per power cord in printing mode Printer 11 A 2.1 kW HP Latex 560/570 200-240 V 50 / 60 Hz Curing 10 A 1.9 kW Introductory Information 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
Introductory Information
9
English
Error code
Recommendation
78.2:01
The back tension is lost. This could be due to a loose roll core or an imminent end
of roll. If these are not the causes, try unloading and reloading the substrate.
78.3:08
Printing with the ink collector is not available in this print mode.
79:03
79:04
79.2:04
19.10:04
19.11:04
19.12:04
Generic firmware error. Update the printer’s firmware.
81:01
81.1:01
81:03
It was impossible to stop the servo correctly before setting the encoder position.
1.
Turn off the printer.
2.
Open the window, observing all safety procedures, and check for any visible
obstacles restricting the movement of the drive roller. If there is a wrinkled
mass of substrate inside the substrate path, clear the obstruction.
3.
Turn on the printer.
86:01
86.2:01
There is a problem in the carriage assembly.
1.
Turn off the printer.
2.
Open the window, observing all safety procedures, and check for any visible
obstacles restricting the movement of the drive roller. If there is a wrinkled
mass of substrate inside the substrate path, clear the obstruction.
3.
Turn on the printer.
87:01
The scan-axis encoder strip is detecting errors in the carriage position. Clean the
encoder strip by following the appropriate process in the front panel menu.
89:11
89.1:10
89.2:10
Some printzone LEDs may be failing or disconnected. The printer will continue
operating normally, with only this functionality affected.
94:01
Color cannot be calibrated on this substrate. White substrate measurement is out
of range.
94:02
Inconsistent colors found.
1.
Check that the substrate-type selection in the front panel corrresponds to an
actual substrate loaded.
2.
Retry calibration.
94:08
Color calibration failed. Try again. See more details about the color calibration
functionality in the user guide.
98:03
One or more printheads are malfunctioning. Use the printhead status plot to find
out which printheads are malfunctioning, and replace them.
Power specifications
Specification
HP Latex 560/570
Printer
Curing
Input voltage
200–240 V
Input frequency
50 / 60 Hz
Maximum load current (per power cord)
11 A
10 A
Power consumption per power cord in printing mode
2.1 kW
1.9 kW