HP Latex 570 Site preparation guide - Page 12

Wall receptacles and power cords, WARNING

Get HP Latex 570 PDF manuals and user guides View all HP Latex 570 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Figure 2-1 Electrical configuration diagram (for reference only) NOTE: The Power Distribution Unit (PDU) must be rated to meet the power requirements of the printer, and shall be in accordance with the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. WARNING! Do not use a power strip (relocatable power tap) to connect both power cords. Wall receptacles and power cords Two power cords are provided with your printer, according to the printer's electrical specifications. If those cords do not reach your PDU and/or UPS, a certified electrician must install suitable extension cables on the day of installation. To make sure you have the right wall socket outlets (wall receptacles) ready for installation, check the following: 1. The wall socket outlets must be suitable for printer input ratings. See Single phase power on page 7. 2. The wall socket outlets must be suitable for the power cord plug type used in the country of installation. The Table 2-6 HP Latex 5x0 Printers - Power cord specifications for printer ratings 200-240, 13A on page 9 list examples of the power cords and the plugs provided with the printer according to the country. To make sure you have the right wall receptacle, find your country in the appropriate table and check the plug type. WARNING! Use only use the power cord supplied by HP with the printer. Do not use a power strip (relocatable power tap) to connect both power cords. Do not damage, cut or repair the power cord. With a damaged power cord, there is risk of fire and electric shock. Always replace a damaged power cord with an HP-approved power cord. Two power cords are provided with the HP Latex 5x0 printer according to printer electrical specifications. If the two cords do not reach the PDU and/or UPS, a certified electrician must install suitable extension cables on the day of installation. The following table lists several examples of the power cord provided with the printer. 8 Chapter 2 Site preparation requirements ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
Figure 2-1
Electrical
configuration
diagram (for reference only)
NOTE:
The Power Distribution Unit (PDU) must be rated to meet the power requirements of the printer, and
shall be in accordance with the Electrical Code requirements of the local jurisdiction of the country where the
equipment is installed.
WARNING!
Do not use a power strip (relocatable power tap) to connect both power cords.
Wall receptacles and power cords
Two power cords are provided with your printer, according to the printer's electrical
specifications.
If those cords
do not reach your PDU and/or UPS, a
certified
electrician must install suitable extension cables on the day of
installation.
To make sure you have the right wall socket outlets (wall receptacles) ready for installation, check the following:
1.
The wall socket outlets must be suitable for
printer input ratings
. See
Single phase power
on page
7
.
2.
The wall socket outlets must be suitable for the
power cord plug type
used in the country of installation.
The
Table
2
-
6
HP Latex 5x0 Printers — Power cord
specifications
for printer ratings 200-240, 13A
on page
9
list examples of the power cords and the plugs provided with the printer according to the
country. To make sure you have the right wall receptacle,
find
your country in the appropriate table and
check the
plug type
.
WARNING!
Use only use the power cord supplied by HP with the printer. Do not use a power strip
(relocatable power tap) to connect both power cords. Do not damage, cut or repair the power cord. With a
damaged power cord, there is risk of
fire
and electric shock. Always replace a damaged power cord with an
HP-approved power cord.
Two power cords are provided with the HP Latex 5x0 printer according to printer electrical
specifications.
If the two cords do not reach the PDU and/or UPS, a
certified
electrician must install suitable extension cables on
the day of installation.
The following table lists several examples of the power cord provided with the printer.
8
Chapter 2
Site preparation requirements
ENWW