HP OmniBook 3100 HP OmniBook 2100 and 3100 PC User’s Handbook - Not O - Page 48

Startup Problems

Get HP OmniBook 3100 - Notebook PC PDF manuals and user guides View all HP OmniBook 3100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

If an I/O card stops communicating properly • It may have been reset if the OmniBook suspended or turned off. Exit and restart the application. If the serial or parallel port is not working • Check the port connection (may be loose). • Check settings in BIOS Setup. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. From the System Devices menu, check that Parallel Port or Serial Port is enabled. Startup Problems If the OmniBook doesn't respond at turn-on • Connect the ac adapter. • Press blue power to try turning on the unit. • Reset the OmniBook. If you get no response, remove the battery and ac adapter-then plug in the ac adapter and try resetting. If you still get no response, the unit requires service. If the OmniBook doesn't boot from battery power • Make sure the battery is properly inserted. • Check battery level on status panel and battery LEDs. • Check battery contacts. If available, try another battery. If the OmniBook doesn't boot from the floppy disk drive • Check the boot order in the BIOS Setup utility. 1. From the Start menu, shut down, then restart the OmniBook. 2. When you see the HP logo, press F2 to enter the BIOS Setup utility. 3. Open the Boot menu. The default boot order is • Diskette Drive • Hard Drive • CD-ROM Drive 4. If Diskette Drive is not option 1, use the arrow keys to select Diskette Drive. 5. Press F6 to move up (or F5 to move down) in the list. 6. Press F10 to Save and Exit the BIOS Setup utility. • Check that the Floppy Boot option in the BIOS Setup utility is enabled. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
48
If an I/O card stops communicating properly
•
It may have been reset if the OmniBook suspended or turned off. Exit and
restart the application.
If the serial or parallel port is not working
•
Check the port connection (may be loose).
•
Check settings in BIOS Setup.
1. From the Start menu, shut down, then restart the OmniBook.
2. When you see the HP logo, press F2 to enter the BIOS Setup utility.
3. From the System Devices menu, check that Parallel Port or Serial Port is
enabled.
Startup Problems
If the OmniBook doesn’t respond at turn-on
•
Connect the
ac
adapter.
•
Press blue power to try turning on the unit.
•
Reset
the OmniBook.
If you get no response, remove the battery and
ac
adapter—then plug in the ac
adapter and try
resetting.
If you still get no response, the unit requires service.
If the OmniBook doesn’t boot from battery power
•
Make sure the battery is properly inserted.
•
Check battery level on status panel and battery LEDs.
•
Check battery contacts. If available, try another battery.
If the OmniBook doesn’t boot from the floppy disk drive
•
Check the boot order in the BIOS Setup utility.
1. From the Start menu, shut down, then restart the OmniBook.
2. When you see the HP logo, press F2 to enter the BIOS Setup utility.
3. Open the Boot menu. The default boot order is
•
Diskette Drive
•
Hard Drive
•
CD-ROM Drive
4. If Diskette Drive is not option 1, use the arrow keys to select Diskette Drive.
5. Press F6 to move up (or F5 to move down) in the list.
6. Press F10 to Save and Exit the BIOS Setup utility.
•
Check that the Floppy Boot option in the BIOS Setup utility is enabled.