HP Presario B1200 Compaq Presario B1200 Notebook PC - Maintenance and Service - Page 78

Remove the system board, until it rests at an angle.

Get HP Presario B1200 - Notebook PC PDF manuals and user guides View all HP Presario B1200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

2. Loosen the captive standoff (2) on the fan that secures the system board to the base enclosure. 3. Flex the left side of the base enclosure (1) until the USB, RJ-45, and RJ-11 jacks (2) clear the openings in the base enclosure. 4. Use the optical drive connector (1) to lift the left side of the system board (2) until it rests at an angle. 5. Remove the system board (3) from the base enclosure by pulling it away at an angle. Reverse this procedure to install the system board. 70 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
2
.
Loosen the captive standoff
(2)
on the fan that secures the system board to the base enclosure.
3
.
Flex the left side of the base enclosure
(1)
until the USB, RJ-45, and RJ-11 jacks
(2)
clear the openings
in the base enclosure.
4
.
Use the optical drive connector
(1)
to lift the left side of the system board
(2)
until it rests at an angle.
5
.
Remove the system board
(3)
from the base enclosure by pulling it away at an angle.
Reverse this procedure to install the system board.
70
Chapter
4
Removal and replacement procedures