HP Pro x360 Maintenance and Service Guide - Page 52

WLAN module, Remove the Phillips M2.0 × 4.5 screw

Get HP Pro x360 PDF manuals and user guides View all HP Pro x360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

1. Prepare the computer for disassembly (see Preparation for disassembly on page 42). 2. Remove the bottom cover (see Bottom cover on page 42). 3. Disconnect the battery cable from the system board (see Battery on page 43). Remove the eMMC storage device: 1. Remove the Phillips M2.0 × 4.5 screw (1) that secures the eMMC storage device to the computer. 2. Lift the edge of the eMMC storage device (2) opposite the socket until it rests at an angle. 3. Pull the eMMC storage device (3) away from the socket at an angle to remove it. NOTE: eMMC storage devices are designed with a notch to prevent incorrect insertion. To install the eMMC storage device, reverse the removal procedures. WLAN module To remove the WLAN module, use this procedure and illustration. Table 5-3 WLAN module descriptions and part numbers Description Intel 9560 ac 2×2 + Bluetooth 5.0 MU-MIMO M.2 2230 non-vPro 160 MHz MIPI+BRI WW WLAN module Intel Wi-Fi 6 AX201 ax 2×2 + Bluetooth 5.0 MU-MIMO M.2 2230 non-vPro 160 MHz MIPI+BRI WW WLAN module with two antennas Spare part number L22634-002 L92724-002 IMPORTANT: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore device functionality, and then contact technical support. Before removing the WLAN module, follow these steps: WLAN module 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
42
).
2.
Remove the bottom cover (see
Bottom cover
on page
42
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
43
).
Remove the eMMC storage device:
1.
Remove the Phillips M2.0 × 4.5 screw
(1)
that secures the eMMC storage device to the computer.
2.
Lift the edge of the eMMC storage device
(2)
opposite the socket until it rests at an angle.
3.
Pull the eMMC storage device
(3)
away from the socket at an angle to remove it.
NOTE:
eMMC storage devices are designed with a notch to prevent incorrect insertion.
To install the eMMC storage device, reverse the removal procedures.
WLAN module
To remove the WLAN module, use this procedure and illustration.
Table 5-3
WLAN module descriptions and part numbers
Description
Spare part number
Intel 9560 ac 2×2 + Bluetooth 5.0 MU-MIMO M.2 2230 non-vPro 160 MHz MIPI+BRI WW WLAN module
L22634-002
Intel Wi-Fi 6 AX201 ax 2×2 + Bluetooth 5.0 MU-MIMO M.2 2230 non-vPro 160 MHz MIPI+BRI WW WLAN
module with two antennas
L92724-002
IMPORTANT:
To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your country
or region. If you replace the module and then receive a warning message, remove the module to restore device
functionality, and then contact technical support.
Before removing the WLAN module, follow these steps:
WLAN module
45