HP Pro x360 Maintenance and Service Guide - Page 61

Connector board high-speed ZIF connector cable, Sensor board ZIF connector cable

Get HP Pro x360 PDF manuals and user guides View all HP Pro x360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Table 5-7 System board descriptions and part numbers (continued) Description Spare part number Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, 64 GB eMMC storage, without N00440-601 WWAN capability, and the Windows 11 operating system Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, 64 GB eMMC storage, without N00440-001 WWAN capability, and a non-Windows operating system Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, without WWAN capability, and N00436-601 the Windows 11 operating system Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, without WWAN capability, and N00436-001 a non-Windows operating system Before removing the system board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 42). 2. Remove the bottom cover (see Bottom cover on page 42). 3. Disconnect the battery cable from the system board (see Battery on page 43). When you replace the system board, be sure to remove the following components (as applicable) from the defective system board and install them on the replacement system board: ● eMMC storage device (see eMMC storage device on page 44). ● WLAN module (see WLAN module on page 45). ● Heat sink (see Heat sink on page 56). Remove the system board: 1. Disconnect the following cables from the system board: ● (1) Connector board low-speed ZIF connector cable ● (2) Connector board high-speed ZIF connector cable ● (3) Webcam/microphone module ZIF connector cable ● (4) Sensor board ZIF connector cable ● (5) Display panel cable ZIF connector cable ● (6) WLAN module shield The WLAN module shield is included in the Plastics Kit, spare part numbers N05694-001 and N02672-001. ● (7) WLAN module antenna cables ● (8) Power connector cable ● (9) Speaker cable ● (10) RTC battery cable ● (11) Keyboard ZIF connector cable 54 Chapter 5 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Table 5-7
System board descriptions and part numbers
(continued)
Description
Spare part
number
Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, 64 GB eMMC storage, without
WWAN capability, and the Windows 11 operating system
N00440-601
Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, 64 GB eMMC storage, without
WWAN capability, and a non-Windows operating system
N00440-001
Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, without WWAN capability, and
the Windows 11 operating system
N00436-601
Equipped with an Intel Pentium Silver N6000 1.1 GHz processor, 4 GB of system memory, without WWAN capability, and
a non-Windows operating system
N00436-001
Before removing the system board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
42
).
2.
Remove the bottom cover (see
Bottom cover
on page
42
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
43
).
When you replace the system board, be sure to remove the following components (as applicable) from the
defective system board and install them on the replacement system board:
●
eMMC storage device (see
eMMC storage device
on page
44
).
●
WLAN module (see
WLAN module
on page
45
).
●
Heat sink (see
Heat sink
on page
56
).
Remove the system board:
1.
Disconnect the following cables from the system board:
●
(1)
Connector board low-speed ZIF connector cable
●
(2)
Connector board high-speed ZIF connector cable
●
(3)
Webcam/microphone module ZIF connector cable
●
(4)
Sensor board ZIF connector cable
●
(5)
Display panel cable ZIF connector cable
●
(6)
WLAN module shield
The WLAN module shield is included in the Plastics Kit, spare part numbers N05694-001 and N02672-001.
●
(7)
WLAN module antenna cables
●
(8)
Power connector cable
●
(9)
Speaker cable
●
(10)
RTC battery cable
●
(11)
Keyboard ZIF connector cable
54
Chapter 5
Removal and replacement procedures for authorized service provider parts