HP Scitex FB750 Site Preparation Guide - Page 14

Computer and networking requirements

Get HP Scitex FB750 PDF manuals and user guides View all HP Scitex FB750 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Rigid-cut sheet media should be stored flat and not stored for long periods before use. Any warping of this media will increase the likelihood of the carriage striking it during printing, or media feed problems. Due to the tendency of synthetic rigid media to build up an electrostatic charge, ESD abatement measures such as raising the relative humidity in the room or draping copper grounding tinsel over the stored media may be necessary. Inks and solvent containers must be properly sealed and stored in the upright position in a flame-proof storage cabinet. WARNING! Do not permit smoking or open flames in the print production or storage areas, and prominently display the appropriate warning signs. WARNING! To avoid electrical shocks or burns caused by the use of wrong type of fire extinguisher, make sure your fire extinguisher has been approved for use on electrical fires. NOTE: It is recommended that substrate rolls remain in their sealed wrapping material when placed in storage. It is advisable to move them from the storage area to the print production area at least 24 hours before use, so that they may reach the required moistness and operating temperature. Computer and networking requirements The printer receives print jobs from an external RIP. You must have the RIP software, server hardware, network interface card, and local area network (100 Mbit or faster required) available for installation with the printer. Consult your HP representative for a list of supported RIPs. Refer to the RIP documentation for the system requirements. The printer and RIP should be connected to the local area network via a switch (preferably 1000 MBit or gigabit) or directly to network wall outlets. The customer is responsible for providing the Ethernet cabling for these connections. Network cables are not included with the printer. RIP requirements The software and hardware requirements of the RIP is as follows. HP Scitex ONYX Thrive 211 RIP (v 11.1.2) ● Main Workstation requirements: ◦ Operating System: Microsoft Windows 7 Professional operating system (SP1 or higher) Windows 8 Professional NOTE: 32-bit operating systems have a hardware limit of 4GB of RAM. It is recommended you use 64-bit operating systems for high volume workflows. ◦ Processor: Intel Core i7 or Equivalent ◦ RAM: 4 GB/processing core ◦ Hard Drive ◦ Multiple Hard Drives 8 Chapter 2 Site planning ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Rigid-cut sheet media should be stored flat and not stored for long periods before use. Any warping of this
media will increase the likelihood of the carriage striking it during printing, or media feed problems.
Due to the tendency of synthetic rigid media to build up an electrostatic charge, ESD abatement measures
such as raising the relative humidity in the room or draping copper grounding tinsel over the stored media
may be necessary.
Inks and solvent containers must be properly sealed and stored in the upright position in a flame-proof
storage cabinet.
WARNING!
Do not permit smoking or open flames in the print production or storage areas, and prominently
display the appropriate warning signs.
WARNING!
To avoid electrical shocks or burns caused by the use of wrong type of fire extinguisher, make
sure your fire extinguisher has been approved for use on electrical fires.
NOTE:
It is recommended that substrate rolls remain in their sealed wrapping material when placed in
storage. It is advisable to move them from the storage area to the print production area at least 24 hours
before use, so that they may reach the required moistness and operating temperature.
Computer and networking requirements
The printer receives print jobs from an external RIP. You must have the RIP software, server hardware,
network interface card, and local area network (100 Mbit or faster required) available for installation with the
printer. Consult your HP representative for a list of supported RIPs. Refer to the RIP documentation for the
system requirements.
The printer and RIP should be connected to the local area network via a switch (preferably 1000 MBit or
gigabit) or directly to network wall outlets. The customer is responsible for providing the Ethernet cabling for
these connections. Network cables are not included with the printer.
RIP requirements
The software and hardware requirements of the RIP is as follows.
HP Scitex ONYX Thrive 211 RIP (v 11.1
.2
)
●
Main Workstation requirements:
◦
Operating System: Microsoft Windows 7 Professional operating system (SP1 or higher) Windows 8
Professional
NOTE:
32-bit operating systems have a hardware limit of 4GB of RAM. It is recommended you
use 64-bit operating systems for high volume workflows.
◦
Processor: Intel Core i7 or Equivalent
◦
RAM: 4 GB/processing core
◦
Hard Drive
◦
Multiple Hard Drives
8
Chapter 2
Site planning
ENWW