Home » HP Manuals » Servers » HP Server tc2120 » Manual Viewer

HP Server tc2120 HP 2100S SCSI RAID - User Guide (337208-001) - Page 29

Installing Adaptec SCSI RAID Software, Microsoft Windows 2000

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

4 Installing Adaptec SCSI RAID Software Microsoft Windows 2000 The following sections describe procedures for installing Adaptec SCSI RAID controllers under Windows 2000. Two installation scenarios are described in this chapter: • Installing on a new system • Adding to an existing system IMPORTANT: The driver for Windows 2000 does not include a digital signature. You may receive one or more warning messages about this condition. Bypass the warnings and continue with the installation. The driver will function normally when the upgrade or install is complete. It is necessary to make adjustments to certain Adaptec 2100S RAID Controller setups to ensure uninterrupted service. This document describes these setups and presents corrective action. Power Management with Windows 2000 Under Windows 2000, it is recommended that you disable Power Options while the Adaptec 2100S RAID Controller is building, rebuilding, or being verified. Otherwise, when the system enters Standby or Hibernate Mode, the Adaptec 2100S RAID Controller operation will stop. HP 2100S SCSI RAID Controller User Guide 4-1

Section	Page
HP 2100S SCSI RAID Controller User Guide	1
Notice	2
Contents	3
About This Guide	7
Audience Assumptions	7
Important Safety Information	7
Symbols on Equipment	7
Symbols in Text	8
Getting Help	9
Technical Support	9
HP Website	9
Authorized Reseller	10
Reader’s Comments	10
Chapter 1: Introduction	11
Read This First	11
About the Documentation	11
System Requirements	12
Working with Electricity	12
Preventing Electrostatic Discharge	12
Chapter 2: About Your New Controller	13
Introduction	13
Adaptec SCSI RAID Feature Overview	13
DC Power Requirements	14
Environmental Specifications	15
Cache Memory	15
2100S Features	15
Board Layout	17
Cache Memory Module	18
Adapted SCSI RAID Controller LEDs	18
LED Display During Power-Up	18
LED Display During Controller Idle	19
LED Display During Controller Active	19
Cache Status LEDs	20
Chapter 3: Installing Your Controller	21
Installation Overview	21
Configuration	22
Narrow and Wide SCSI	22
Configuring Cables	22
Configuring SCSI Termination	23
Configuring Device IDs	25
Installation	25
Installing Cache Memory Modules	25
Installing the Controller	26
Determining the Booting Controller	27
Controller IRQ and Address	27
NVRAM Reset	28
Chapter 4: Installing Adaptec SCSI RAID Software	29
Microsoft Windows 2000	29
Power Management with Windows 2000	29
Installing on a New System	30
Adding to an Existing System	31
Appendix A: Regulatory Compliance Notices	32
Regulatory Compliance Statements	32
Federal Communications Commission Radio Frequency Interference Statement	32
European Union Compliance Statement	33
Australian/New Zealand Compliance Statement	34
Canadian Compliance Statement	34
Japanese Compliance (Voluntary Control Council Initiative)	34
End-User Software License Agreement	34
Appendix B: Electrostatic Discharge	37
Grounding Methods	38
Appendix C: Troubleshooting	39
	39
Problem 1	39
Solution 1	39
Problem 2	40
Solution 2	40
Problem 3	40
Solution 3	40
Problem 4	41
Solution 4	41
Problem 5	41
Solution 5	41
Problem 6	42
Solution 6	42
Problem 7	43
Solution 7	43
Problem 8	43
Solution 8	43
Problem 9	44
Solution 9	44
Problem 10	44
Solution 10	44
Problem 11	45
Solution 11	45
Problem 12	45
Solution 12	45
Problem 13	46
Solution 13	46
Problem 14	46
Solution 14	46
Problem 15	47
Solution 15	47
Problem 16	47
Solution 16	47
Problem 17	48
Solution 17	48
Problem 18	48