HP StorageWorks SN6000 HP StorageWorks 8/20q Fibre Channel Switch event messag - Page 29

Data EFMD frame. The port, Security Attributes ESA

Get HP StorageWorks SN6000 - Fibre Channel Switch PDF manuals and user guides View all HP StorageWorks SN6000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Table 4 Alarm events and recommended action (Continued) Icon Event ID and message Description Action (A1006.0006) (Zoning conflict, device_WWN and device_WWN do not share an ACL hard zone, but device_WWN share a soft zone) (A1007.0001) (Security: Unspecified zoning enforcement error) The named zone members cannot communicate because they are members of different hard zones. Place both zone members in the same hard zone or exclude both from hard zones. A device was not authorized or it failed security checks and will not be allowed to join the fabric. None (A1007.0002) (Security: Remote Switch with WorldWide Name (WWN) wwn configured for chap, no chap configured for local switch. 2-way Authentication Failure) The device worldwide name (WWN) is either not configured in the security database, or it is not configured for Challenge Handshake Authentication Protocol (CHAP). Add the device WWN to the active security set if it missing, or modify the group to allow for CHAP authentication with the other devices. (A1007.0005) (Security: Authentication request was rejected by port.) Indicates that a remote switch rejected a security authentication attempt. The port will isolate. Checks the security configuration on the remote switch to determine the problem. (A1007.0006) (Security: Could not validate Authentication Response from port_number, payload seems to be incorrect.) The format of the payload of the response frame does not match what was expected. Check for errors on the remote side of the link. Check the transceiver and cable. Update firmware on remote switch. (A1007.0007) (Security: Fabric Binding (ESA) not supported on remote switch and Fabric Binding is enabled, failing security checks) Either fabric binding is not enabled on the remote switch or the remote switch does not support security at all. Check the security configuration on the remote switch. (A1007.0008) (Security: ESA Response failure, failing security checks) A failure was received during processing of the Exchange Security Attributes (ESA) received frame. Either the payload did not match the standard layout or the payload status indicated a reject. Check for errors on the remote side of the link. Check the transceiver and cable. Update firmware on the remote switch. (A1007.0009) (Security checks EFMD response failure, failing security check.) A remote switch rejected an Exchange Fabric Membership Data (EFMD) frame. The port will be isolated. Check the remote switch for the reason that the EFMD frame was rejected. It is possible that the FabricBindingEnabled parameter is different on the two switches. 8/20q Fibre Channel Switch event messages reference guide 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
8/20q Fibre Channel Switch event messages reference guide
29
(A1006.0006) (Zoning
conflict,
device_WWN
and
device_WWN
do not
share an ACL hard zone,
but
device_WWN
share a
soft zone)
The named zone members
cannot communicate because
they are members of different
hard zones.
Place both zone members in
the same hard zone or
exclude both from hard
zones.
(A1007.0001) (Security:
Unspecified zoning
enforcement error)
A device was not authorized
or it failed security checks
and will not be allowed to
join the fabric.
None
(A1007.0002) (Security:
Remote Switch with
WorldWide Name (WWN)
wwn
configured for
chap, no chap
configured for local
switch. 2-way
Authentication Failure)
The device worldwide name
(WWN) is either not
configured in the security
database, or it is not
configured for Challenge
Handshake Authentication
Protocol (CHAP).
Add the device WWN to the
active security set if it missing,
or modify the group to allow
for CHAP authentication with
the other devices.
(A1007.0005) (Security:
Authentication request
was rejected by
port
.)
Indicates that a remote switch
rejected a security
authentication attempt. The
port will isolate.
Checks the security
configuration on the remote
switch to determine the
problem.
(A1007.0006) (Security:
Could not validate
Authentication Response
from
port_number
,
payload seems to be
incorrect.)
The format of the payload of
the response frame does not
match what was expected.
Check for errors on the
remote side of the link. Check
the transceiver and cable.
Update firmware on remote
switch.
(A1007.0007) (Security:
Fabric Binding (ESA)
not supported on remote
switch and Fabric
Binding is enabled,
failing security
checks)
Either fabric binding is not
enabled on the remote switch
or the remote switch does not
support security at all.
Check the security
configuration on the remote
switch.
(A1007.0008) (Security:
ESA Response failure,
failing security
checks)
A failure was received during
processing of the Exchange
Security Attributes (ESA)
received frame. Either the
payload did not match the
standard layout or the
payload status indicated a
reject.
Check for errors on the
remote side of the link. Check
the transceiver and cable.
Update firmware on the
remote switch.
(A1007.0009) (Security
checks EFMD response
failure, failing
security check.)
A remote switch rejected an
Exchange Fabric Membership
Data (EFMD) frame. The port
will be isolated.
Check the remote switch for
the reason that the EFMD
frame was rejected. It is
possible that the
FabricBindingEnabled
parameter is different on the
two switches.
Table 4
Alarm events and recommended action (Continued)
Icon
Event ID and message
Description
Action